GYTC8S / GYXTC8S Fiber Optic Cable

The cross-section of GYTC8SCable's is in the shape of "8". The steel strand is suspended, and the double-sided plastic-coated corrugated steel belt forms excellent flattening resistance. With self-supporting overhead steel strand, much installation time and cost is saved.

As one of the professional optical fibre manufacturing companies, TUOLIMAhas been manufacturing fiber optic cable including gytc8s or gyxtc8s cable for over 10 years with ISO, UL, RoHS, REACH certificates. The reliable quality of TUOLIMA products has won its popularity across five continents and the spread is growing. You can check the details of our GYTC8S / GYXTC8S Fiber Optic Cable on this page. Or you can consult us directly, if you have any questions about TUOLIMA GYTC8S / GYXTC8S Fiber Optic Cable.

Details of GYTC8S&GYXTC8S Fiber Optical Cable

The structure of the standard figure-eight self-supporting stranded optical cable is that multimode or single mode fiber optic cables are sheathed in a loose tube made of high modulus plastic, and the tube is filled with a water blocking compound. The center of the cable core is a metal reinforced core. For certain fiber optic cables, a layer of polyethylene needs to be squeezed outside the metal-reinforced core. The loose tube (and filler rope) is twisted around the central reinforced core to form a compact and Round cable core, the gap in the cable core is filled with water blocking filler. The cable core is longitudinally wrapped with steel-plastic composite tape, and placed in parallel with the steel strands while extruding a figure-eight sheath into a cable.

Item		Description
Fiber counts of cable		8
Loose tube	Material	PBT
		8
	tube	1
	Diameter(mm)
	Filling compound Material	Thixotropic jelly
Suspension wire	Material	Metallic strengthen member
	Diameter
		3000
Crush Resistance (N/100mm)		7990
Operating Temperature(℃)		0 ~ +60

Characteristics of GYTC8S&GYXTC8S Fiber Optical Cable

Optical fiber characteristics (G.652D FIBER)

	Description		Specifications
Category			Before cabling		After cabling
Optical Specifications	Attenuation @1550 nm		≤0.20 dB/km (max.)		≤0.22 dB/km (max.)
	Attenuation @1625 nm		≤0.23dB/km		≤ 0.24 dB/km
	Zero Dispersion Wavelength		≤1520 nm
	Zero Dispersion Slope		≤ 0.084 ps/nm2·km
	Polarization Mode Dispersion(PMD)		≤0.08 ps/km
	Cable Cutoff Wavelength (λcc)		≤1450 nm
	Macro bending Loss		≤ 0.05 dB
	(1 turn; Ф32 mm) @1550 nm		≤ 0.05 dB
	(100 turns; Ф60 mm) @1625 nm		≤0.05 dB
	(100 turns; Ф50 mm) @1310 &@1625 nm
	Mode Field Diameter	@1550 nm
Dimensional	Cladding Diameter
Specifications	Core/clad concentricity error		≤0.6μm
	Cladding Non-Circularity		≤1.0%
Mechanical	Min bending radius		(static)	25D (dynamic)
Specifications	Proof Test level		≥1.2%
	Fiber Curl Radius		≥4.0m
	Peak Coating Strip Force

Specification of GYTC8S / GYXTC8S Fiber Optic Cable

No	Item	Test standard	Method	Acceptance criteria
1	Tensile	IEC-60794-1-E1		-Fiber strain at maximum
	test		Sample length:50 meters	Load: max. 0.33%
			Time: 1minutes;	-Attenuation increase≤0.10dB
2	Crush	IEC-60794-1-E3	Load:1000N	-No splits or cracks in the
	test		Time: 1 minutes	outer jacket;
			Length: 100mm	-Attenuation increase<0.10dB,
3	Impact	IEC-60794-1-E4	Impact energy: 450g	-No splits or cracks in the outer jacket
	test		Height:1 meter	-Attenuation increase≤0.10dB
			Impact points: min.1
			Number of impacts: 5
4	Repeated bending	IEC-60794-1-E6	R=20×cable outer diameter	- No splits or cracks in the outer jacket
			1m cable length with 150N weight,30 cycles	-Attenuation increase ≤0.10dB
5	Torsion	IEC-60794-1-E7	1m cable length with 150N weight	- No splits or cracks in the outer jacket
	test		±180 degrees, 10 cycles	-Attenuation increase ≤0.10B
6	Bending	IEC-60794-1-E11	Diameter of mandrel: 20×D	- No splits or cracks in the outer jacket
	test		Number of turns/helix:10	- No fiber break
			Number of cycles: 5
7	Temperature cycling test	IEC-60794-1-F1	Temperature step: +20℃→0℃→+60℃→0℃→	-Attenuation variation for reference value(the attenuation to be measured before test at +20±3℃) ≤0.10dB,
			+60℃→+20℃
			Time per each step: 12 hrs
			Number of cycles: 2 cycles
8	Water penetration test	IEC-60794-1-F5	Water height: 1m	-No water leakage at the end of the sample
			Sample length:3m
			Duration of test: 24hrs
9	Drip test	IEC-60794-1-E14	Five 0.3m samples suspended vertically in a climate chamber, raised temperature to +70℃	-No filling compound shall drip from tubes after 24 hr

Advantages of GYTC8S / GYXTC8S Fiber Optic Cable

Use high-quality optical fiber to ensure that the optical cable has excellent transmission performance

Accurately control the excess length of the outdoor fiber optic cable to ensure that the optical cable has excellent mechanical and high/low-temperature characteristics

Full-section water-blocking structure to ensure good water-blocking and moisture-proof performance

The loose tube is filled with special grease to protect the optical fiber critically

The longitudinally clad steel tape strengthens the resistance to lateral pressure of the optical cable

Packing and Comments of GYTC8S/GYXTC8S Fiber Optic Cable

Packing material: Non-returnable wooden drum.

Both ends of cable are securely fastened to drum and sealed with a shrinkable cap to prevent ingress of moisture.

Cable printing: The sequential number of the cable length shall be marked on the outer sheath of the cable at an interval of 1meter ± 1%.

The following information shall be marked on the outer sheath of the cable at an interval of about 1 meter.

Cable type and number of optical fiber

Manufacturer name

Month and Year of Manufacture

Cable length

Drum marking: Each side of every wooden drum shall be permanently marked in a minimum of 2.5~3 cm high lettering with following:

Manufacture name and logo

Cable length

Cable type and number of fibers

Roll way

Gross and net weight

Other supplier products

	Air Blown Fiber Optic Cable	Fiber optic air blown cable is a kind of fiber optic cable that uses air delivery during installation. The air blowing principle is to use high-pr...
	A Type Fiber Optic Fast Connector	The quick SC / APC connector incorporates a new disposable wedge tool system, eliminating the need for specialized expansion tools. SC/ APC fibe...
	TLM-P Dead-end Guy Grips	The TLM-P dead end guy gripor preformed guy gripis widely used for the installation of bare conductors or overhead insulated conductors for transmi...
	0.9mm Fiber Optic Pigtail	The drop cable pigtailis a fiber optic cable terminated with a factory installed connector at one end, leaving the other end terminated. Therefo...
	ADSS Fiber Optic Cable	Fiber Optic ADSS Cableis known as all dielectric self-supporting optical cable. Self-supporting ensures that the adss fiber optic cable has suffici...

All supplier products

Same products

	6242B 6243B LSZH Flat Cores +Earth Cable	Seller: Guangdong Jinlianyu Cable industrial Co.,Ltd	CU/LSZH/lszh flat cableare the electric cables referred to thermosetting insulated and thermoplas...
	GYTC8S / GYXTC8S Fiber Optic Cable	Seller: Hangzhou Tuolima Network Technologies Co., Ltd	The cross-section of GYTC8SCable's is in the shape of "8". The steel strand is suspended, and the...
	DFGJ Magnetic Cylinder Sensor	Seller: ALIF TECH. CO., LTD.	DFGJ series magnetic sensor DFGJ series L-slot cylinder specially used for AIRTAC 7.1*3.2, whi...
	3 Cores +1 Earth Power Cable (XLPE Insulated)	Seller: Guangdong Jinlianyu Cable industrial Co.,Ltd	The structure of 3 cores+1 earth cable wire is designed for application where the earth wires are...
	PLC TYPE WDM	Seller: T&S COMMUNICATIONS CO., LTD.	Instead of taking a thin film filter to mux or demux wavelengths, PLC type achieves the same goal...