XFP-10G-ZR 10Gbps XFP Optical Transceiver
XFP-10G-ZR
10Gbps XFP Optical Transceiver
Features:
Supports 9.95Gb/s to 11.3Gb/s Bit Rates；
Hot-pluggable XFP Footprint；
Maximum Link Length up to 80km；
Temperature-Stabilized EML transmitter ；
Duplex LC Connector；
Built-in Digital Diagnostic Functions ；
Dispersion Tolerance 800ps/nm；
Compliant with RoHS；
Operating Case Temperature Standard: 0~ 70 °C
Application:
OC192/ STM 64；
10GBASE-ZR/ZW 10G Ethernet ；
1200-SM-LL-L 10G Fiber Channel ；
P1L1-2D2；
ITU-T G.709ONT
Regulatory Compliance:
|
Feature |
Standard |
Performance |
|
Electrostatic Discharge (ESD) Tothe Electrical Pins |
MIL-STD-883E Method 3015.7 |
Class 1C(>1000 V) |
|
Electromagnetic Interference(EMI) |
FCC Part 15 Class B EN55022:2006 CISPR 22B :2006 VCCI Class B |
Compliant with standards Noise frequency range: 30 MHz to 6 GHz. Good system EMI design practice required to achieve Class B margins. System margins depend on customer host board and chassis design. |
|
Electrostatic Discharge to theenclosure |
EN 55024:1998+A1+A2 IEC-61000-4-2；GR-1089-CORE |
Compatible with standards |
|
Immunity |
EN 55024:1998+A1+A2 IEC 61000-4-3 |
Compliant with standards. 1kHz sine-wave, 80% AM, from 80 MHz to 1 GHz. No effect on transmitter/receiver performance is detectable between these limits. |
|
Laser Eye Safety |
FDA 21CFR 1040.10 and 1040.11 EN60950, EN (IEC) 60825-1,2 |
CDRH compliant and Class I laser |
Description:
The transceiver is small form factor pluggable module for duplex optical data communications such as 10GBASE-ZR/ZW defined by IEEE 802.3ae. It is with the XFP 30-pin connector to allow hot plug capability；
This module is designed for single mode fiber and operates at a nominal wavelength of 1550 nm. The transmitter section uses a 1550nm EML, which is class 1 laser compliant according to International Safety Standard IEC-60825.
The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC.
Send product request
Other supplier products
 |
Fiber Optic Polishing | Fiber Optic Polishing For use in Fiber Optic (Ferrule) Grinding and Polishing Product specification: New Version: 66XC，66HPL，66HPX，66P ，5"(127mm) ... |
 |
Outdoor Optical Fiber Cable Armoured Loose Tube Fiber Cable | Outdoor Optical Fiber Cable Armoured Loose Tube Fiber Cable Feature: Steel-wire parallel member,filler protect tube fiber steel tape amored; Excel... |
 |
bps SFP Optical Transceiver（MMF） | Features: Data-rate of 1.25Gbps； 850nm VCSELLaser and PIN photodetector； Compliant with SFP MSA and SFF-8472； Duplex LC receptacle ； Digital... |
 |
Plug-in attenuator SC female-E2000APC Male | Plug-in attenuatorSC female-E2000APC Male Description: Available in FC, SC, LC, ST and MU plug type. They are suitable for connection through pane... |
 |
155Mbps SFP Optical Transceiver（SMF） | 155Mbps SFP Optical Transceiver（SMF） Features: Up to 155Mbps data-rate； Compliant with SFP MSA and SFF-8472； Duplex LC receptacle ； Digital Diagnos... |
Same products
 |
GJS-D021 Dome Fiber Optic Splice Closure | Seller: "Shanghai Grandway Telecom Tech.Co.,Ltd. | Functions Type D021 dome closure fiber opticcan be used for aerial,underground, pipeline and wal... |
 |
GJS-D010 Dome Fiber Optic Splice Closure | Seller: "Shanghai Grandway Telecom Tech.Co.,Ltd. | GJS-D010 Dome Fiber Closure Functions Type D010 fiber optic splice enclosurecan be used for a... |
 |
Indoor FTTH Drop Cable | Seller: "Shanghai Grandway Telecom Tech.Co.,Ltd. | Functions With the development of fiber optic communication, FTTH has been the final solution of... |
 |
F2H-OTB-A Series Indoor Optical Termination Box | Seller: "Shanghai Grandway Telecom Tech.Co.,Ltd. | Functions F2H-OTB-A Series indoor fiber termination boxis used as terminal equipment of otb fibe... |
 |
F2H-FOSC-ODP Fiber Optic Splice & Splitter Closure | Seller: "Shanghai Grandway Telecom Tech.Co.,Ltd. | Functions F2H-FOSC-ODP Fiber Optic Splice & Splitter Closure applies vented structure and me... |
