Full car environmental simulation chamber supplier

Whats/App: +86 156 1874 6768

Web: standard-groups.com

Application

The Full Vehicle Environmental Performance Test Chamber is applicable across a range of vehicle performance evaluation scenarios, including:

Vehicle HVAC and Thermal Management Testing

Evaluation of air conditioning, heating, defrosting, and demisting efficiency

Thermal comfort assessment for driver and passenger compartments

Emission and Air Quality Testing

Measurement of in-cabin pollutants and VOC concentrations

Analysis of temperature-dependent emission characteristics

Road Simulation and Performance Analysis

Coupled with roller-type chassis dynamometers to simulate driving conditions

Testing fuel consumption, energy efficiency, and climate control performance

Standards

The chamber conforms to multiple national and international standards, including:

(1) GB 18352.6-2016 – Limits and measurement methods for light vehicle pollutants

(2) GB/T 27630-2011 – Guidelines for passenger car interior air quality assessment

(3) QC/T 658-2009 – Road test methods for automotive air conditioning system performance

(4) GB/T 12535-2021 – Vehicle starting performance test methods

(5) GB/T 12542-2020 – Road test methods for vehicle thermal balance capabilities

(6) GB/T 2423 – Environmental testing methods for high/low temperature, humidity, and thermal cycling

(7) ISO 12219-1 – Road vehicles – Interior air – Test methods for volatile organic compounds in complete vehicles

(8) DIN 75220 – Sunlight simulation aging tests for automotive components

(9) SAE J1711 – Recommended procedures for hybrid vehicle fuel economy and emission measurements

(10) PV 3938 – Evaluation methods for automotive interior odor

Parameters

Item	Specification
Internal dimensions (L×W×H)	16.300 × 8.300 × 5.200 mm
Heat exchanger clearance height	≥3.500 mm
Floor insulation	150 mm polyurethane
Chamber floor	Stainless steel tread plate, solid layer thickness ≥3 mm, pattern height 2 mm
Floor load capacity	1.200 kg/wheel; axle load ≥2.000 kg
Chassis dynamometer support	Thermally insulated, designed for full dynamometer weight
Vehicle access door	1 set, net 3.000×3.000 mm, two-leaf, heated glass observation windows 300×300 mm
Personnel access door	1 set, net 900×1.900 mm, heated explosion-proof glass observation window 300×300 mm
Control observation window	2 sets (optional), 2.000×1.000 mm, insulated, anti-frost heated surface
Lighting	Main illumination ≥500 lux over full temperature range; emergency light operational ≥1 hour at -40°C
Power outlets	4×220 VAC/10A, 2×220 VAC/16A, 2×380 VAC/32A (with standard triangle plugs)
Cable feed-throughs	4 sets, diameter 100 mm, max 16 cables per hole
Personnel airlock	1 set, 1.500×1.500×2.100 mm, internal opening, external lockable
Chamber pressure	Micro-positive pressure 0–50 Pa via pressure balance valves

Test Procedures

Pre-Test Preparation

Clean chamber walls with neutral detergent (pH≥7.5) and rinse with deionized or distilled water

Ventilate chamber at least six air changes to reduce background pollutants: formaldehyde ≤6 µg/m³, TVOC ≤50 µg/m³, single pollutants ≤5 µg/m³

Verify calibration of temperature/humidity sensors, solar simulation system (e.g., 1.200 W/m² ±20 W/m²), and roller dynamometer if installed

Sample and Parameter Setup

Position vehicle centrally within chamber, ensuring level orientation and uniform airflow over vehicle surfaces

Connect vehicle power supply and sensors (temperature, fuel consumption, emission monitoring)

Test Process Control

Activate automated control system to monitor and maintain temperature, humidity, solar intensity, and airflow (e.g., roller fan speed up to 260 km/h)

For thermal cycling tests, program temperature rise, hold, and drop phases while recording vehicle performance metrics (cold start, AC cooling rate, etc.)

Safety and Emergency Measures

Continuously monitor chamber pressure and emission concentrations

System triggers alarms and shuts down power if temperature deviates by >±2°C or emissions exceed limits

Entering the chamber requires stopping the test and ventilating for at least 30 minutes

Maintenance Information

Regular cleaning of chamber walls, doors, and observation windows to prevent contamination

Periodic calibration of temperature, humidity, and solar simulation systems

Inspection of power outlets, lighting, and emergency systems

Verification of airlock operation and pressure balance valves

Scheduled maintenance of roller dynamometer interface and support structures

Other supplier products

	Floor Scrubber Air Performance Testing Equipment	Whats/App: +86 156 1874 6768 Web: standard-groups.com TheFloor Scrubber Air Performance Testing Equipmentis designed for comprehensive evaluation...
	High Temperature Voltage Breakdown Tester for Dielectric Strength Testing	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards GB1408.1-2016 "Test method for Electrical Strength of Insulating M...
	Scratch resistance test equipment	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application The Scratch Resistance Test Machine is suitable for a wide range of materials ...
	Face Mask Tensile Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Face Mask Tensile Tester is designed to measure tensile strength, elongation at break, ...
	Geotextile-Bentonite Cushion Permeameter	Whats/App: +86 156 1874 6768 Web: standard-groups.com The geotextile-bentonite cushion is a finished waterproof soil mat with excellent water-ret...

All supplier products

Same products

	Two-Shot Injection Molds	Seller: WIT MOLD LIMITED	Two-Shot Injection Molds Advantages of two-shot injection molding The benefits of Double Inject...
	precision injection molding	Seller: WIT MOLD LIMITED	precision injection molding Precision injection moldingis a method demanding unparalleled accura...
	Custom Plastic Molds molding	Seller: WIT MOLD LIMITED	Custom Plastic Molds molding Plastic Molds molding servicesprovide many extremely versatile part...
	Thermoset Molding	Seller: WIT MOLD LIMITED	Thermoset Molding Key Aspects of Thermoset Molding Materials: Thermosetting Polymers:These inc...
	PE Film Scrap, Rolls, Bale, Regrinds, Lump, LLDPE, HDPE, LDPE	Seller: Plastic scrap, ferrous and non-ferrous metal scraps supplier for recycling	We have PE film scrap, including LLDPE, HDPE, and LDPE, available for ongoing shipment to buyers ...