Single chip liquid crystal touch impact testing machine
Product Introduction:
Liquid crystal touch impact testing machine is mainly used for hard plastics （including sheet, pipe, plastic profile）， reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.
Standards:
GB/T 18910.101-2021
IEC 60068-2-75:2014
Main features:
Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.
Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.
Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.
Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.
Performance parameters:
1. Simple beam impact testing machine
- Impact speed: 2.9m/s
- Impact energy: 1/2/4/5J
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 230mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz（single-phase three-wire system）
2. Cantilever beam impact testing machine
- Impact speed: 3.5m/s
- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J（3 hammers, customer's choice）
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 335mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz（single-phase three-wire system）
Send product request
Other supplier products
 |
Automobile Seat Frame Strength Test Bench-QINSUN | Applicable standards: The National Standard of the People's Republic of China (GB) : such asGB 15083. this standard specifies the strength requi... |
 |
Qinsun SUNTEST Weathering Instruments | A practical desktop xenon lamp equipment with various accessories, customized to meet your SUNTEST needs. Here, you can see SunCool cooling device ... |
 |
Paper absorbance tester | Introduction: It is an instrument used to determine the surface water absorption of coated paper and cardboard, including corrugated board. It is ... |
 |
Automatic Wire Stripping Machines | Product Introduction: Automobile wire cutting tester is the main instrument for testing the insulation strength of automobile wire, and it is th... |
 |
IBC cleaning systems,ibc cleaning equipment,high pressure ibc washer | Model Semi-automatic IBC tote washer Spray angle 360° Material stainless steel Max. Pressure 150 bar Voltage 380V (or on request) Voltage of IB... |
Same products
 |
Common Rail Injector Valve F00R J02 012 | Seller: 868983 | Common Rail Injector Valve F00R J02 012 David Chen |
 |
Common Rail Injector Valve F00R J02 005 | Seller: 868983 | Common Rail Injector Valve F00R J02 005 David Chen |
 |
Common Rail Injector Valve F00R J01 945 | Seller: 868983 | Common Rail Injector Valve F00R J01 945 David Chen |
 |
Common Rail Injector Valve F00R J01 941 | Seller: 868983 | Common Rail Injector Valve F00R J01 941 David Chen |
 |
Common Rail Injector Valve F00R J01 924 | Seller: 868983 | Common Rail Injector Valve F00R J01 924 David Chen |
