Shoes Sole Bending Resist Testing Machine

Bennewart Flex Tester is used to test outsole flexing resistance by flexing the outsole at a certain speed and angle. The shoe outsole flexing method aims to check the effect of sole materials and surface patterns on cut growth. This whole sole flexing tester methods meet ISO 20344, ISO 17707, DIN 53543 and etc.

Application:

This EN Sole Flexing Tester bennewart flexing machine is used to measure the flexing resistance of shoe soles under continuous movement. Before test, plunge some holes at the maximum bending position, and mount specimen at both grips, one fixed, one movable. Specimen runs flexing owing to the movement of machine. After a certain test cycles, remove the specimen and check its difference of incision length.

Feature：

Plunge some holes at the maximum bending position, and mount specimen at both grips, one fixed, one movable. Specimen runs flexing owing to the movement of machine. After a certain test cycles, remove the specimen and check its difference of incision length.

Bennewart Flex Test Procedure:

Remove the heel from the outsole and clam the outsole according to the standard. Make sure the outsole would be fully flexed in the right position. Then to cut the sample with an equipped chisel(cutting cool) to the required length, the cut should be parallel to the bennewart flex machine. Pre-set the machine to run 30,000 cycles. After it finished the pre-set cycles, check the cut growth and any change of the outsole. For more information, welcome to contact us at any time!

Parameter:

Control mode：Touch screen controlled

Bending angle：90±2 °

Bending speed：125-150cpm

Mandrel diameter：30 mm

Clamps apart：110±1mm

Movable fixture stroke：41.5 ± 0.5 mm

Counting：0-9999999

Power supply ：1∮AC 220V 50/60HZ

Dimensions：105x42x60cm

Weight：About 90kg

Standards:

SATRA TM161,

ISO 17707,

ISO20344-2021 section8.6 ,

ISO20347 section 5.8.4,

AS/NZS 2210.2 section8.4.2

GB/T 20991 section8.4.2,

QB/T 2885, DIN 53543

Other supplier products

	General Ventilation Test Bench - Test Equipment	According to the ISO16890-2016 standard, the test bench is mainly used for the testing of general ventilation air filters. Based on the performance...
	Carbon Arc Weathering Tester	Carbon Arc Weathering Tester utilizes eight sunlight carbon arc lamps capable of providing approximately 78 hours of continuous illumination. These...
	Fabric Negative-ion Concentration Tester - Test Equipment	Standard GB/T 30128-2013: Textiles – Test and Evaluation of Negative Ion Generation Application Functional Textile R&D: Assesses air-p...
	Alcohol abrasion tester	The Alcohol Abrasion Tester is designed for evaluating the wear and friction resistance of coatings, prints, and surfaces under controlled laborato...
	EN20344 Sole Flexing Tester	Install the sole test piece on the EN sole flexing testing machine, so that the incision falls just above the center of the rotating shaft of the E...

All supplier products

Same products

	Air Intake Filter Test System	Seller: Standard Groups	The Air Intake Filter Test System is designed for testing industrial air filters and engine air f...
	Mattress Spring Fatigue Tester，ASTM D3574 ，how to test mattress for sagging	Seller: Standard International Group (HK) Limited	The King Size Foam Fatigue Tester is a single-station pneumatic fatigue testing system designed f...
	Mattress Rollator，ASTM F1566 ，Mattress Durability Tester，Mattress Fatigue Tester	Seller: Standard International Group (HK) Limited	The Mattress Rollator is a laboratory durability testing system designed to evaluate the long-ter...
	HD2 Pneumatic Foam Fatigue Tester，ISO 3385，Foam Fatigue Testing Machine	Seller: Standard International Group (HK) Limited	The HD2 Pneumatic Foam Fatigue Tester is a heavy-duty, single-station laboratory testing machine ...
	VW Heel Abrasion Tester，ISO 4649 ，Heel Performance Testing Machine	Seller: Standard International Group (HK) Limited	The VW Heel Abrasion Tester is designed to evaluate the wear resistance of floor covering materia...