Thermal Protective Performance Tester (TPP)
The Thermal Protective Performance (TPP) Test Device was developed to measure the time elapsed for convective and radiant heat to penetrate through a protective composite fabric system - measuring the resulting damage to human skin.
Standards：
BS EN ISO 6942. EN 366. EN 407. ISO 11612. ASTM F1939. ASTM F2702. NFPA 1971. NFPA 2112. GB 38543. GB/T 38306
Feature：
Industrial personal computer with analysis software is suitable for severe testing conditions.
Automatic calculation for heat transmission factor and radiant heat transfer index.
Sample holder with force applied kit is easy to operate.
Single pump for shutter movement and cooling water loop.
Parameter：
• Up to 7.5 in x 7.5 in. (19 cm x19 cm) sample size
• Copper slug calorimeter sensors (ASTM or ISO)
• ± 0.75°C temperature measurement
• ± 3% radiant heat flux measurement
• Device Dimensions: 42 in. x 20 in. x 18 in. (107 cm x 51 cm x 46 cm)
• Space Requirements: 46 in. x 26 in. x 24 in. (117 cm x 67 cm x 61cm)
• Power Requirements: 208-265 VAC, 50/60Hz, Single-phase
• Maximum nominal current 20 Amps
• Compressed Air: Clean/dry air at 70-90 PSI, (145 PSI max)
• Cooling Water: Cooling water required, chiller or tap water source is acceptable
• Propane Requirement: Regulated supply at 15 PSI (minimum)
• Water-cooled radiant heat source with 9 quartz (500W) infrared lamps
• Two gas burners with flame detection auto ignition
• Mass flow controller for precise gas control
• Water-cooled protective shutter
• Pneumatic sample carriage and shutter assembly
• Integrated sensor cooling stand (air cooled)
• Emergency stop cuts gas flow, power to lamps and pneumatics
• Tinted tempered glass shield protects operator
• Software safety interlocks monitor water flow, carriage position, burner ignition
Send product request
Other supplier products
 |
Cantilever Fabric Stiffness Tester - Test Equipment | Standard ZB WO4003. GB/T18318. ASTM D 1388. IS09073-7. BS EN22313 Application Fabric Stiffness Tester, is a practical equipment to determine the... |
 |
fatigue testing machine - Test Equipment | Standards ISO 5402: Leather physical testing – Flex tester method for adhesion and strength analysis. SATRA TM55: Seam fatigue testing fo... |
 |
Multi Finger Scratch/Mar Tester | Multi Finger Scratch/Mar Tester uses tungsten carbide as a scratch to accurately detect surface damage caused by unconventional physical forms (suc... |
 |
Water injection counterweight dummy | Testing Equipment | Product Introduction This counterweight dummy can be filled with water, the torso and the bottom are separated, independently filled with water o... |
 |
Cantilever Fabric Stiffness Tester | Standard ZB WO4003. GB/T18318. ASTM D 1388. IS09073-7. BS EN22313 Application Fabric Stiffness Tester, is a practical equipment to determine the... |
Same products
 |
Blanket Flammability Test Machine | Seller: Standard Groups | Bed Blanket Flammability Tester-It is mainly used for testing the flame retardant performance of ... |
 |
High Temperature Oxygen Index Tester | Seller: Standard Groups | The High-Temperature Oxygen Index (TOI) measuring instrument determines oxygen index at up to 125... |
 |
Limiting Oxygen Index Tester | Seller: Standard Groups | The Limiting Oxygen Index Tester measures the minimum oxygen concentration needed to sustain comb... |
 |
Vertical Flammability Tester | Seller: Standard Groups | Vertical Flammability Chamber for measuring the vertical flame spread for children’ sleepwe... |
 |
45 Degree Flammability Tester | Seller: Standard Groups | Application 45 Degree Flammability Tester is used to determine the burning characteristics of te... |
