Computer controlled memory impact testing machine，bench-top Computer controlled memory impact testing machine
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Computer controlled memory impact testing machine is mainly used for hard plastics, reinforced nylon, glass steel, ceramics, cast stone, electrical insulation materials and other non-metallic materials impact toughness determination. The testing machine is an ideal test equipment for chemical industry, scientific research units, colleges and universities, quality testing departments, professional manufacturers laboratories and other units. It is a testing instrument with simple structure, convenient operation and accurate and reliable data.
Computer controlled memory impact testing machine is mainly used for hard plastics, reinforced nylon, glass steel, ceramics, cast stone, electrical insulation materials and other non-metallic materials impact toughness determination. The testing machine is an ideal test equipment for chemical industry, scientific research units, colleges and universities, quality testing departments, professional manufacturers laboratories and other units. It is a testing instrument with simple structure, convenient operation and accurate and reliable data.
Application
Tapered twin-screw extruders are primarily used for direct forming of pipes, sheets, and profiles from materials such as rigid polyvinyl chloride (UPVC), while also serving as plastic modifiers and pelletizers for powder materials. With different molds, they can directly extrude sheets, pipes, and profiles for experimental purposes.
Standards
JB/T 11343-2013：Martindale Abrasion and Pilling Tester
JB/T 5420-2014：Fabric Abrasion Tester
JB/T 6492-2014：Fabric Pilling Tester
JB/T 6491-2015：Fabric Snagging Tester
T/GDPIA 21-2020：Test Method for Abrasion and Pilling Resistance of Textiles (Martindale Method)
T/GDPIA 16-2020：Test Method for Fabric Pilling Resistance
T/GDPIA 22-2020：Test Method for Fabric Snagging Resistance
T/ZZB 1351-2019：Specification for Fabric Abrasion and Pilling Tester
T/CPMIA 0201-2022：Test Method for Abrasion Resistance of Textile Materials (Martindale Method)
Features
Screw Structure and Motion:
Conical Design: The feed section features a larger diameter, while the homogenizing section has a smaller diameter, creating a forced thrust to prevent material overheating.
Counter-Rotation: Two screws mesh in opposite directions, conveying material axially through the screw gap while applying shear force. Ideal for processing plastics like PVC and polyolefins.
Plasticizing and Extrusion Process:
Heating and Cooling: Built-in cast aluminum heaters and cooling fans within the barrel, combined with gradient temperature control technology, precisely regulate the processing temperature range.
Vacuum Degassing: Ensures uniform plasticization and minimizes bubbles and impurities through a vacuum degassing system.
Energy Efficiency and Environmental Protection:
Variable Frequency Drive: Compatible with VFD motors for energy-saving operation.
Waste Heat Recovery: Selected upgraded models incorporate waste heat recovery systems to further enhance energy efficiency.
Technical Parameters
| Category | Specification |
|---|---|
| Impact Energy | 2/4 J (simply supported beam); 2.75/5.5 J (cantilever) |
| Sampling Rate | 10 µs |
| Resolution | 16 bits |
| Load Measurement Accuracy | ≤ 1% |
| Impact Knife Angle | 30° |
| Pendulum Torque (Simply Supported Beam) | 2.1436 Nm, 1.0718 Nm, 0.5359 Nm |
| Pendulum Torque (Cantilever Beam) | 2.9474 Nm, 1.4737 Nm |
| Pendulum Pre-lift Angle | 150° |
| Simply Supported Beam | |
| Impact Speed | 2.9 m/s |
| Distance from Pendulum Shaft Center to Sample Center | 230 mm |
| Blade Angle | 30° |
| Blade Radius | 2 mm |
| Support Corner Radius | 1 mm |
| Support Front Angle | 5° |
| Support Rear Angle | 10° |
| Support Span | 40. 60. 70 mm |
| Sample Type and Size (L × W × T) | 380×10×4 mm, 50×6×4 mm, 120×15×10 mm |
| Cantilever Beam | |
| Impact Speed | 3.5 m/s |
| Distance from Pendulum Shaft Center to Sample Center | 335 mm |
| Blade Angle | 75° |
| Blade Radius | 0.8 mm |
| Front Edge Angle | 5° |
| Blade Back Angle | 10° |
| Sample Type and Size (L × W × T) | 80×10×4 mm63.5 × 12.7 × 12.7 mm63.5 × 12.7 × 6.4 mm63.5 × 12.7 × 3.2 mm |
Pre-Operation Checks
Equipment Status: Inspect switches and instrument functions; verify protective devices are intact.
Personal Protection: Wear earplugs, safety goggles, gloves, etc.
Material Preparation: Clean the storage bin; fill with material after confirming no impurities.
Equipment Installation and Commissioning
Secure Installation: Ensure equipment is firmly fixed to prevent displacement.
Electrical Connections: Inspect wiring and address any anomalies.
No-Load Test Run (for new equipment or after major overhaul):
Start the lubricating oil pump and inspect the lubrication system.
Start the main motor at low speed and check current, voltage, and transmission system.
Gradually increase rotational speed while observing noise changes.
Activate the feeding system and inspect the feed screw.
Start the vacuum pump and inspect the vacuum system.
Measure the heating section temperature; deviation from the instrument reading must not exceed 3°C.
Shut off the heating power supply and activate the cooling system.
Test the emergency stop button.
Startup Operation
Preheat: Power on and heat to the specified temperature, then maintain for 20 minutes.
Manual Rotation: Manually rotate the screw in the specified direction to confirm no abnormalities.
Check Rotation Direction: Facing the discharge head, clockwise rotation indicates right-hand screw.
Start Main Unit: Synchronously activate the power supply, gradually adjust the speed, and progressively increase it.
Feeding: Closely monitor the amperage meter and indicator gauge; torque must not exceed 65%-75% of the main motor's power rating.
Operational Monitoring
Vacuum Degassing: After the main unit stabilizes, start the vacuum pump, adjust water flow, and observe material plasticization status.
Temperature Control: Use the intelligent temperature controller to maintain minimal temperature fluctuations.
Fault Handling: Regularly inspect overload protection and fault alarm systems.
Operation Conclusion
Power Off: Turn off the equipment power after operation concludes.
Cleaning and Maintenance: Implement safety precautions and perform regular maintenance.
Send product request
Other supplier products
 |
Schopper Abrasion Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards DIN 53863. Part 2: Abrasion test methods for textile fabrics (rotary abrasion te... |
 |
Battery combustion tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Battery Combustion Tester is designed for safety evaluation of lithium-ion batteries by... |
 |
ASTM D6595 Carbon Black Dispersion Test Equipment | Whats/App: +86 156 1874 6768 Web: standard-groups.com The carbon black content tester is a precision instrument specifically designed for measuri... |
 |
Fiber Crimp Elasticity Test machine | Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Introduction: YG362C fiber crimp elasticity meter is used for crimp degree of 1-22... |
 |
ISO 5660 Cone Calorimeter Fire Test Equipment Supplier Factory Direct | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Features Ignition System 10 kV spark igniter with fire-off safety system; p... |
Same products
 |
MMA-120 Handheld Arc Welder | Seller: 871183 | The MMA-120 Handheld Arc Welder from ChuangLi Electronic Technology Co., Ltd. is designed for con... |
 |
SHX Series Circulating Fluidized Bed Steam Boiler | Seller: Hebei Genjux Boiler Co.,Ltd | Capacity: 10-35 t/hWorking pressure: 1.25-2.5 MPaOperating temperature: 194-400 ℃Applicable to bi... |
 |
YQ(Y)W Series Oil/Gas Fired Vertical Thermal Oil Boiler | Seller: Hebei Genjux Boiler Co.,Ltd | Capacity: 7000-29200 KWOperating pressure: 0.8-1.0 MPaOperating temperature: 320℃Operating mode: ... |
 |
DHL Series Coal-Fired Steam Boilers | Seller: Hebei Genjux Boiler Co.,Ltd | Capacity: 35-75 t/hOperating pressure: 1.25-5.4 MPaOperating temperature: 194-485℃Applicable to b... |
 |
SZL Series Biomass Steam Boiler | Seller: Hebei Genjux Boiler Co.,Ltd | Capacity: 6-35 t/hWorking pressure: 1.0-2.5 MPaOperating temperature: 184-350 ℃Applicable fuel bi... |
