Temperature humidity vibration chamber with RF absorption
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Applications
The Transparent Absorbing Wave Temperature and Humidity Vibration Test Chamber is a high-end testing device capable of simulating complex environmental conditions. It is particularly well-suited for reliability verification in fields such as aerospace, aviation, and automotive electronics. By superimposing temperature-humidity cycles with vibration stress, it rapidly exposes potential defects in products during transportation or use.
Standards
JJF 1101 Calibration Specification for Temperature and Humidity of Environmental Test Equipment
GB/T 5170 Inspection Methods for Environmental Test Equipment for Electrical and Electronic Products
Features
ombined temperature, humidity, and vibration testing to simulate real-world multi-stress environments
High-performance transparent wave door with excellent X-band transmission efficiency
Integrated absorbing wave materials to minimize electromagnetic reflection and standing wave interference
Wide temperature and humidity operating range suitable for extreme environmental testing
High thermal load capacity to support powered test samples during operation
Stable structural design ensuring long-term flatness and mechanical reliability
Parameters
| Category | Item | Specifications |
|---|---|---|
| Basic Specifications | Nominal Inner Volume | 9.5 m³ |
| Inner Chamber Dimensions | 2700mm × 1800mm × 1950mm (Depth × Width × Height) | |
| Test Environment Conditions | Ambient temperature: 25°C, relative humidity: ≤85% RH, cold water temperature: ≤28°C | |
| Temperature Performance | Temperature Range | -70°C ~ +100°C |
| Temperature Fluctuation | ≤±0.5°C | |
| Temperature Deviation | ≤±2°C | |
| Temperature Uniformity | ≤2°C | |
| Temperature Ramp Rate | - Heating: ≥10°C/min (equivalent load 1000kg, electric heating power 8kW, average across the whole range; ≥10°C/min from room temperature to -55°C, ≥10°C/min from -55°C to 70°C)- In the range of -55°C ~ +85°C, the chamber can withstand an internal heat load of 8000W- In the range of -55°C ~ +85°C, the chamber can withstand an internal heat load of 3500W and an internal cooling air supply of 100kg/h (air temperature: 2~35°C, dew point temperature: ≤40°C) | |
| Humidity Performance | Humidity Range | 35% RH ~ 98% RH (adjustable within -20°C ~ 70°C) |
| Humidification Method | Humidification via hot air passing through the test piece; alternating temperature and humidity (typical value: 30°C/60°C, RH95%, temperature change rate ≥85%); constant temperature and humidity (typical value: 35°C, 90% ~ 98%) | |
| Humidity Deviation | ≤±3% RH (when humidity >75% RH); ≤±5% RH (when humidity ≤75% RH) | |
| Chamber Front Door | Door Configuration | Hermetic door with transparent viewport- Temperature resistance: -65°C ~ +105°C- Humidity resistance: 25% ~ 98% RHFunctional performance:1) Working frequency: X-band2) Temperature resistance range: -65°C ~ +105°C3) Humidity resistance range: 25% ~ 98% RH4) Wave transmission rate: >95%5) Standing wave ratio influence: <2%6) Power resistance: 10W/cm²7) Flatness: |
| Chamber Front End | Absorber Material (on Hermetic Door) | - Wave transmission rate (X-band): >95% (on left, right, and upper sides)- Power resistance: 10W/cm²- Total mass loss (TWC): ≤0.6%- Volatile condensable material (CVCM): ≤ |
Test Procedures
To conduct a standard combined environmental test, you should follow these steps:
Install the test specimen securely on the vibration platform and connect required power and signal interfaces.
Set the desired temperature, humidity, and vibration profiles according to the test specification.
Start the temperature and humidity control system and allow conditions to stabilize.
Activate the vibration system and run the combined environmental test for the specified duration.
Monitor key parameters throughout the test and record all relevant data.
After test completion, return the chamber to ambient conditions before removing the specimen.
Send product request
Other supplier products
 |
In-situ expansion analysis system | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard ASTM E83: Standard Test Method for Verification of Linear Displacement Measurin... |
 |
Female Side Impact Dummy | Whats/App: +86 156 1874 6768 Web: standard-groups.com The 5th Percentile Female Side Impact Dummy is a next-generation biomechanical surrogate de... |
 |
High-Temperature Reciprocating Friction and Wear Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The High-Temperature Reciprocating Friction and Wear Tester is designed for quantitative ev... |
 |
Coatings Shear | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard YY/T 0856-2011 (China): Specifies mechanical testing protocols for metal angular ... |
 |
Multi-Purpose Tribology Testing Equipment | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications You can use this tester for: Friction and wear testing of metals, ceramics, ... |
Same products
 |
ER4043 Silicon Aluminum Welding Wire | Seller: 868776 | Hangzhou Kunli Welding Materials Co., Ltd. offers ER4043 Silicon Aluminum Welding Wire for alumin... |
 |
HDPE High Speed Water Cooled Double Wall Corrugated Pipe Extrusion Line | Seller: Shandong HUASU Plastic Technology Co.,Ltd. | The molds adopt the double flow channel structure and nitriding polishing processed die head. Thi... |
 |
PanEVAP & MVR system | Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
