Temperature humidity vibration chamber with RF absorption
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Applications
The Transparent Absorbing Wave Temperature and Humidity Vibration Test Chamber is a high-end testing device capable of simulating complex environmental conditions. It is particularly well-suited for reliability verification in fields such as aerospace, aviation, and automotive electronics. By superimposing temperature-humidity cycles with vibration stress, it rapidly exposes potential defects in products during transportation or use.
Standards
JJF 1101 Calibration Specification for Temperature and Humidity of Environmental Test Equipment
GB/T 5170 Inspection Methods for Environmental Test Equipment for Electrical and Electronic Products
Features
ombined temperature, humidity, and vibration testing to simulate real-world multi-stress environments
High-performance transparent wave door with excellent X-band transmission efficiency
Integrated absorbing wave materials to minimize electromagnetic reflection and standing wave interference
Wide temperature and humidity operating range suitable for extreme environmental testing
High thermal load capacity to support powered test samples during operation
Stable structural design ensuring long-term flatness and mechanical reliability
Parameters
| Category | Item | Specifications |
|---|---|---|
| Basic Specifications | Nominal Inner Volume | 9.5 m³ |
| Inner Chamber Dimensions | 2700mm × 1800mm × 1950mm (Depth × Width × Height) | |
| Test Environment Conditions | Ambient temperature: 25°C, relative humidity: ≤85% RH, cold water temperature: ≤28°C | |
| Temperature Performance | Temperature Range | -70°C ~ +100°C |
| Temperature Fluctuation | ≤±0.5°C | |
| Temperature Deviation | ≤±2°C | |
| Temperature Uniformity | ≤2°C | |
| Temperature Ramp Rate | - Heating: ≥10°C/min (equivalent load 1000kg, electric heating power 8kW, average across the whole range; ≥10°C/min from room temperature to -55°C, ≥10°C/min from -55°C to 70°C)- In the range of -55°C ~ +85°C, the chamber can withstand an internal heat load of 8000W- In the range of -55°C ~ +85°C, the chamber can withstand an internal heat load of 3500W and an internal cooling air supply of 100kg/h (air temperature: 2~35°C, dew point temperature: ≤40°C) | |
| Humidity Performance | Humidity Range | 35% RH ~ 98% RH (adjustable within -20°C ~ 70°C) |
| Humidification Method | Humidification via hot air passing through the test piece; alternating temperature and humidity (typical value: 30°C/60°C, RH95%, temperature change rate ≥85%); constant temperature and humidity (typical value: 35°C, 90% ~ 98%) | |
| Humidity Deviation | ≤±3% RH (when humidity >75% RH); ≤±5% RH (when humidity ≤75% RH) | |
| Chamber Front Door | Door Configuration | Hermetic door with transparent viewport- Temperature resistance: -65°C ~ +105°C- Humidity resistance: 25% ~ 98% RHFunctional performance:1) Working frequency: X-band2) Temperature resistance range: -65°C ~ +105°C3) Humidity resistance range: 25% ~ 98% RH4) Wave transmission rate: >95%5) Standing wave ratio influence: <2%6) Power resistance: 10W/cm²7) Flatness: |
| Chamber Front End | Absorber Material (on Hermetic Door) | - Wave transmission rate (X-band): >95% (on left, right, and upper sides)- Power resistance: 10W/cm²- Total mass loss (TWC): ≤0.6%- Volatile condensable material (CVCM): ≤ |
Test Procedures
To conduct a standard combined environmental test, you should follow these steps:
Install the test specimen securely on the vibration platform and connect required power and signal interfaces.
Set the desired temperature, humidity, and vibration profiles according to the test specification.
Start the temperature and humidity control system and allow conditions to stabilize.
Activate the vibration system and run the combined environmental test for the specified duration.
Monitor key parameters throughout the test and record all relevant data.
After test completion, return the chamber to ambient conditions before removing the specimen.
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
High precision warm body dummy tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Meet the standard ISO15831.GB/T 39605-2020 Scope of application Building heat ventilatio... |
 |
Metal Wire Repeated Bending Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Metal Wire Repeated Bending Tester is designed to evaluate the bending fatigue performa... |
 |
OEM Walk-in Climate Test Chamber Factory Direct | Temperature & Humidity Simulation Solutions | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards GB/T 2423.1: Environmental testing methods for electrical and elec... |
 |
6 station fog tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Fogging Tester is mainly used to test the evaporation of volatile components in materials s... |
 |
Limited Oxyen Index Tester，Automatic oxygen index test machine | Whats/App: +86 156 1874 6768 Web: standard-groups.com Introduction STD Limited Oxyen Index Tester for the determination under the test condition... |
