Industrial Multifunction Tribology Testing Equipment Supplier China
Get a quote：
Whats/App: +86 156 1874 6768
Web: standard-groups.com
The Universal Multifunction Tribology Test Machine (UMT Series) is a versatile friction and wear testing system designed for comprehensive tribological evaluation in academic, research, and industrial laboratories. You can perform friction, wear, indentation, and scratch tests on a single platform while obtaining high-precision, repeatable, and reliable data.The system supports extremely low friction coefficient measurement (down to 0.004) and enables rapid generation of Stribeck curves for in-depth lubricant and material performance analysis. Its modular architecture and interchangeable environmental chambers allow you to adapt the system to a wide range of operating conditions while maintaining compliance with major international testing standards.
Standards
The system is compatible with, but not limited to, the following international standards:
(1) ASTM G77 – Block-on-Ring Wear Testing
(2) ASTM G99 – Pin-on-Disk Wear Testing
(3) ASTM G132 – Ball-on-Three-Plate Wear Testing
(4) ASTM G119 – Reciprocating Sliding Wear Testing
(5) ASTM G203 – Reciprocating Wear of Materials
(6) ASTM G204 – Sliding Wear Under Controlled Conditions
(7) ASTM G206 – Oscillatory Wear Testing
(8) ASTM G133 – Linearly Reciprocating Ball-on-Flat Wear Testing
(9) ASTM G174 – Scratch Testing of Materials
(10) ASTM D3702 / ASTM D3704 / ASTM D2981 / ASTM D2509 – Lubricant and Grease Wear and EP Performance
Parameters
Motion Drive Modules
| Drive Type | Typical Applications | Speed / Frequency Range | Torque / Stroke | Applicable Standards |
|---|---|---|---|---|
| Rotary Drive | Ball-on-disk, pin-on-disk, disk-on-disk | 0.1 – 5.000 rpm | Torque up to 5 Nm | ASTM G99. ASTM G132. ASTM D3702 |
| Reciprocating Drive | Ball-on-flat, pin-on-flat, ring-on-sleeve | 0 – 60 Hz (20 Hz @ 25 mm, 40 Hz @ 12.5 mm, 60 Hz @ 2 mm) | Adjustable stroke | ASTM G119. ASTM G203. ASTM G204. ASTM G206 |
| Block-on-Ring Drive | Block-on-ring wear testing | 0.1 – 5.000 rpm | Torque up to 5 Nm | ASTM G77. ASTM D3704. ASTM D2981 |
| Linear Drive | Scratch, indentation, low-speed friction | 0.002 – 10 mm/s | Stroke up to 120 mm | ASTM G174. ASTM G133 |
Sensors and Measurement System
| Sensor Type | Range / Characteristics |
|---|---|
| 2D Force Sensors | Multiple options, measurement range from 1 mN to 2.000 N |
| Acoustic Emission Sensor | Detection of micro-cracks and friction-induced signals |
| Contact Resistance Sensor | Real-time contact state monitoring |
| Micro-Displacement Sensor | High-resolution displacement measurement for scratch and indentation tests |
Power and Interface
| Item | Specification |
|---|---|
| Power Supply | 220 V, single phase, 50/60 Hz |
| Communication Interface | USB connection |
| Control Computer | Standard PC, freely replaceable |
Features
High accuracy and repeatability: You can measure friction coefficients as low as 0.004 with excellent data consistency and rapid Stribeck curve generation.
Modular configuration: Four motion drive modules and multiple environmental chambers allow hundreds of test configurations on a single platform.
Fast module recognition and replacement: Automatic identification enables module changes within 1–3 minutes.
Multi-environment capability: Testing is possible under lubricated, high-temperature, low-temperature, humid, corrosive, and vacuum conditions.
Multi-sensor integration: You can simultaneously measure friction force, acoustic emission, contact resistance, and displacement with high precision.
Accessories
(1) Rotary test module for ball-on-disk and pin-on-disk configurations
(2) Reciprocating test module for ball-on-flat and pin-on-flat testing
(3) Block-on-ring test module
(4) Linear test module for scratch and indentation testing
(5) Interchangeable environmental chambers for lubrication, temperature, humidity, corrosion, and vacuum
(6) Two-dimensional force sensors
(7) Acoustic emission sensor
(8) Contact resistance sensor
(9) Micro-displacement sensor
Send product request
Other supplier products
 |
Resistance Tester for Molten Metal Droplet (Splash) Impact Performance | Whats/App: +86 156 1874 6768 Web: standard-groups.com Performance and Standards: This resistance tester for molten metal droplet (splash) impact ... |
 |
Intramedullary Nails Static Four-point Bending Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard YY/T 0591 (China): Standard for static four-point bending tests of lockable intra... |
 |
EV Battery Fire and Particle Impact Test Equipment UL 2596 Supplier Factory Direct | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Parameters ParameterSpecification Dimensions 1600 × 750 &t... |
 |
ISO Certified Vacuum Cleaner Filter Efficiency Tester Factory | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards IEC 60312-1: Vacuum cleaners for household use – Methods for... |
 |
Camera test light box | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard ISO 12233: Compliant with SFR (Spatial Frequency Response) testing for lens resol... |
Same products
 |
ER4047 Aluminum Mig Welding Wire | Seller: 868776 | Hangzhou Kunli Welding Materials Co., Ltd. specializes in manufacturing reliable welding material... |
 |
ER4043 Silicon Aluminum Welding Wire | Seller: 868776 | Hangzhou Kunli Welding Materials Co., Ltd. specializes in manufacturing high-quality welding mate... |
 |
Choosing the Right Equipment for Heavy-Duty Cleaning | Seller: Taizhou Feike Mechanical Technology Co., Ltd. | FEIKE’s High Pressure Washer is designed for industrial cleaning, equipment maintenance, ve... |
 |
ER4043 Silicon Aluminum Welding Wire | Seller: 868776 | Hangzhou Kunli Welding Materials Co., Ltd. offers ER4043 Silicon Aluminum Welding Wire for alumin... |
 |
HDPE High Speed Water Cooled Double Wall Corrugated Pipe Extrusion Line | Seller: Shandong HUASU Plastic Technology Co.,Ltd. | The molds adopt the double flow channel structure and nitriding polishing processed die head. Thi... |
