Wire and Cable Smoke Density Tester Manufacturer | IEC 61034 Cable Smoke Density Test Chamber Supplier

• 

Get a quote：

Whats/App: +86 156 1874 6768

Web: standard-groups.com

E-mail：info@standard-groups。com

Features

The enclosure consists of a cubic shell with dimensions of 3000mm ± 30mm (length, width, and height). The internal material of the enclosure is SUS 304 stainless steel, filled with calcium silicate fireproof material, and the exterior is made of iron with powder coating;

All internal fixtures are made of stainless steel; aesthetically pleasing and corrosion-resistant;

The total area of the ventilation holes is 50cm² ± 10cm², and they remain open throughout the test; the baffle height is 1000mm;

Equipped with wire and cable test racks and weights as required by the standard.

The test chamber door has glass observation windows on opposite sides, fitted with sealed transparent windows (minimum 100mm x 100mm) that allow light from the horizontal optical measurement system to pass through. These windows are located 2150mm ± 100mm above the ground;

The photocell and light source are positioned at the center of the windows on each of the two walls, without physical contact.

Parameters

Test Procedures

Sample Preparation: Cut a cable or optical fiber sample of the specified length (e.g., ≥1 meter) according to the standard, and condition it at 23℃±5℃ for at least 16 hours.

Equipment Calibration: Calibrate the optical system using filters with different transmittances (e.g., 100%, 75%, 25%) to ensure data accuracy.

Sample Installation: Secure the sample horizontally on the support inside the combustion chamber, adjusting its position so that the distance between the lower surface of the sample and the bottom of the alcohol tray is 150mm±5mm.

Environmental Setup: Measure the temperature inside the combustion chamber door at a height of 1.5m-2.0m from the ground and at least 0.2m from the wall to ensure it is within the range of 25℃±5℃; if necessary, preheat the combustion chamber with a blank test.

Test Start: Ignite the alcohol tray fire source, close the combustion chamber door, and start the fan to ensure even distribution of smoke; the test ends when the fire source is extinguished after 5 minutes or after 40 minutes of testing, whichever comes first, or when the transmittance no longer decreases.

Record Results: Read and record the minimum transmittance (Tmin) during the test, and calculate parameters such as specific optical density (Ds).

Equipment Cleaning: After the test, clean the combustion residue and keep the chamber clean.

Other supplier products

	High and Low Temperature Humidity Test Chamber,IEC 62660	Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications High and Low Temperature Humidity Test Chamber is designed for performance an...
	Liquid Sustained Combustion Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Introduction This product complies with "Recommendations on the Transport of Dange...
	High Precision Combustion Rate Analyzer for Energetic Materials	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards It conforms to the United Nations Recommendations on the Transport...
	Carton drop tester，ASTM D5276 drop tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Carton Drop Tester is designed to simulate the impact experienced by packaging during t...
	UV Test Chamber丨UV Testing Mechine	Whats/App: +86 156 1874 6768 Web: standard-groups.com Features and Benefits 1. STD UV-SI-260 is widely used in UV aging test, which can realiz...

Same products

	HDPE High Speed Water Cooled Double Wall Corrugated Pipe Extrusion Line	Seller: Shandong HUASU Plastic Technology Co.,Ltd.	The molds adopt the double flow channel structure and nitriding polishing processed die head. Thi...
	PanEVAP & MVR system	Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat...
	PanGAP wide gap welded plate heat exchanger	Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel...
	PanBloc welded plate heat exchanger	Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac...
	PanBox welded plate heat exchanger	Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated...