Wire and Cable Smoke Density Tester Manufacturer | IEC 61034 Cable Smoke Density Test Chamber Supplier
Get a quote：
Whats/App: +86 156 1874 6768
Web: standard-groups.com
E-mail：info@standard-groups。com
Features
The enclosure consists of a cubic shell with dimensions of 3000mm ± 30mm (length, width, and height). The internal material of the enclosure is SUS 304 stainless steel, filled with calcium silicate fireproof material, and the exterior is made of iron with powder coating;
All internal fixtures are made of stainless steel; aesthetically pleasing and corrosion-resistant;
The total area of the ventilation holes is 50cm² ± 10cm², and they remain open throughout the test; the baffle height is 1000mm;
Equipped with wire and cable test racks and weights as required by the standard.
The test chamber door has glass observation windows on opposite sides, fitted with sealed transparent windows (minimum 100mm x 100mm) that allow light from the horizontal optical measurement system to pass through. These windows are located 2150mm ± 100mm above the ground;
The photocell and light source are positioned at the center of the windows on each of the two walls, without physical contact.
Parameters
| Technical Parameter | Details |
|---|---|
| Operating Voltage | AC 220 V ± 10%, 50HZ |
| Light Source Voltage | DC 12V |
| Power | 2000W |
| Ambient Temperature | 25℃ ± 5℃ |
| Nominal Luminous Flux | 2000lm ~ 3000lm |
| Nominal Color Temperature | 2800K ~ 3200K |
| Air Flow Rate | ≥ 2L/min |
| Fire Supply Time | Standard time 40min (settable) |
| Timing Accuracy | ≤ 0.5s for 40min |
| Calibration Value | 100% (transmittance) |
Test Procedures
Sample Preparation: Cut a cable or optical fiber sample of the specified length (e.g., ≥1 meter) according to the standard, and condition it at 23℃±5℃ for at least 16 hours.
Equipment Calibration: Calibrate the optical system using filters with different transmittances (e.g., 100%, 75%, 25%) to ensure data accuracy.
Sample Installation: Secure the sample horizontally on the support inside the combustion chamber, adjusting its position so that the distance between the lower surface of the sample and the bottom of the alcohol tray is 150mm±5mm.
Environmental Setup: Measure the temperature inside the combustion chamber door at a height of 1.5m-2.0m from the ground and at least 0.2m from the wall to ensure it is within the range of 25℃±5℃; if necessary, preheat the combustion chamber with a blank test.
Test Start: Ignite the alcohol tray fire source, close the combustion chamber door, and start the fan to ensure even distribution of smoke; the test ends when the fire source is extinguished after 5 minutes or after 40 minutes of testing, whichever comes first, or when the transmittance no longer decreases.
Record Results: Read and record the minimum transmittance (Tmin) during the test, and calculate parameters such as specific optical density (Ds).
Equipment Cleaning: After the test, clean the combustion residue and keep the chamber clean.
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
SAE J400 Gravel Resistant Impact Tester Manufacturer Factory Direct Sale | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Features Airflow Control System: Digital regulation of air pressure (0.2&nda... |
 |
Automatic suture needle elasticity and toughness device | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications Quality Control: In the production process of medical devices, it is used for... |
 |
High-Speed Reciprocating Friction Wear Testing Machine | Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications You can use this tester to: Evaluate the friction and wear performance of va... |
 |
Liquid Sustained Combustion Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Introduction This product complies with "Recommendations on the Transport of Dange... |
 |
Standard light source sample table | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards ISO 3664:2009: Meets international standards for graphic arts and photography vi... |
Похожие товары
 |
Laser Cutting Machines | Продавец: Chanxan (Changshu) Laser Technology Co., Ltd. | Laser Cutting Machines PrecisionLaser Cutting Systemsfor Film, Glass & Industrial Materials ... |
 |
Precision Laser Micromachining Machine | Продавец: Chanxan (Changshu) Laser Technology Co., Ltd. | Precision Laser Micromachining Machine| Ultrafast Laser Micromachining Systems Chanxan provides ... |
 |
Ultrafast Laser Systems | Продавец: Chanxan (Changshu) Laser Technology Co., Ltd. | Ultrafast Laser Systems Femtosecond Laser System Ultra-precision femtosecond laser systemfor hi... |
 |
Industrial Laser Equipment Manufacturer | Продавец: Chanxan (Changshu) Laser Technology Co., Ltd. | Industrial Laser Equipment Manufacturer for Precision Cutting, Marking & Micromachining Chan... |
 |
Common Rail Injector Valve F00R J02 012 | Продавец: 868983 | Common Rail Injector Valve F00R J02 012 David Chen |
