Gas & Water Assisted Injection Mold
gas injection moulding manufacturers
gas injection moulding / gas assist injection moulding / gas assist molding
gas injection mold / gas injection mould
gas assist injection molding design guide
Water & Gas Injection Mold
Since the thermal conductivity and heat capacity of water are much bigger than nitrogen, so the injection cycle of water-assisted is about 70% shorter than the injection cycle of gas injection moulding; The product wall thickness of water-assisted injection molding is more even than gas-assisted; The inner wall roughness of water-assisted injection molding is smoother than that gas-assisted injection molding.
WATER & GAS ASSISTED INJECTION MOLDED PRODUCTS
Gas-assisted injection molding of kettle handles
What is the gas-assisted injection molding? Today we will talk about the case of gas-assisted injection molding of kettle handles. During the injection molding process, push the melt plastic to fi...
TV Frame Mold
Pushing the liquid plastic into the cavity and core side by high pressure during the injection process, and the gas pressure is maintained to form a hollow section inside the thick wall of the plastic part, the injection process is called gas-assisted injection molding.
Bike Frame Mold for Kids
During plastic molding processing, gas-assisted injection molding is abbreviated as GAIM, which is a relatively new molding processing technology, this technology is comprehensively developed on the basis of the design and manufacture of traditional injection molding molds and blow molding molds, and entered the practical stage in the 1990s, gas-assisted injection molding has huge technical application advantages and can produce significant economic benefits.
Car Ceiling Handle Injection Mould
When plastic injection molding, the melt is under the injection pressure and enters the mold cavity, on the same section, the flow rate of each gate is different, the fastest in the middle, the closer to the cavity wall, the slower the flow rate, and it contacts the cavity wall, the speed of the first layer is zero.
Water Assisted Injection Mould
Because the flow rate of the outer layer of the melt is slow and the speed of the inner layer is fast, the inner layer of melt will roll outwards and stick to the mold cavity while advancing.
Engine Coolant Pipe
In the gas-assisted injection molding process, the gas always follows the path with the least flow resistance, from high pressure to low pressure, and flows to the thick wall part, because the temperature of this part is high and the resistance is small.
Plastic Pipe Mold
The booster pressurizes the nitrogen in the low-pressure storage cylinder into workable high-pressure nitrogen, and stores it in the high-pressure nitrogen cylinder, the maximum pressure of the nitrogen can reach 35MPa in the process.
Automotive Water Intake Manifold Mould
Gas injection methods can be divided into two types, one is to inject gas together with the melt through the machine nozzle, and the other is to directly inject gas into the runner or cavity through the gas injection element (gas needle), the latter is divided into single-point intake and multi-point intake.
Gas Assisted & Water Assisted Injection Molding Differences
- Water-assisted injection moldequipment cost is nearly 10 times higher than gas-assisted injection molding, and Water assisted injection molding only can be imported currently;
- custom injection mouldingprocess is more extensive than that of water-assisted injection molding;
Gas-Assisted Injection Molding Process
Gas-assisted injection molding is roughly divided into 4 stages: plastic injection, gas injection, pressure-holding cooling, and gas discharge.
Gas-assisted injection molding classification
- gas assisted injection molded productswhich will not have sink marks or warpage, and meets the requirements of high-quality products.
As one of gas injection moulding manufacturers, we will do our best to meet all the needs of customers.
Send product request
Other supplier products
 |
Plastic Pipe Mold | Plastic Pipe Mold The gas-assisted controller is used to control the pressure of nitrogen to the mold at different times, the controller is divide... |
 |
Medical Plastic Injection Mold | For medical device injection molding companies, it means that medical supervisors are required to supervise and manage the materials used to manufa... |
 |
32 Cavity Mold | 32 Cavity Mold In terms of multi-cavity molds, we pay attention to the design of layout and runner filling balance, which is also the key to the s... |
 |
Cold Runner & Hot Runner Plastic Mold | Generally, the temperature-sensitive wire is composed of steel wire insulated with a heat-sensitive material, the temperature sensing wire is commo... |
 |
Auto Parts Mould | Auto Parts Mould Automotive Parts Moldfeatures: More kinds of molded automotive parts, please visit our website. As one of injection m... |
Same products
 |
For Mercedes-Benz-C-206 Modified Bumper Mould | Seller: Taizhou Huangyan Chenpeng Mould Co., Ltd. | Taizhou Huangyan Chenpeng Mold Co., Ltd. is a professionalwholesale Mercedes-Benz-C-206 Modified ... |
 |
Front Bumper Lower Lip Mould For 2021 Honda CRV | Seller: Taizhou Huangyan Chenpeng Mould Co., Ltd. | Introducing the for 2021 Honda CRV Front Bumper Lower Lip Mould: Elevate Your Driving Experienc... |
 |
Bottle cap mold | Seller: Taizhou Huangyan Yongsheng Mould Co., Ltd. | Taizhou Yongsheng Mould Co., Ltd. can produce cap moulds （）within 64 cavities. The hot runner or ... |
 |
Plastic Injection Mould For 2009 Audi A5 Front Bumper | Seller: Taizhou Huangyan Chenpeng Mould Co., Ltd. | Our Advantage:1.We have developed about 1000 PCS bumper mould since we founded.2.Our company's mo... |
 |
Double Color Mold For Car Head Lighting Two-Shot Mold | Seller: Taizhou Toolsong Mould Co., Ltd. | Double Color Mold For Car Head Lighting Two-Shot Mold Double color lens mold for car head lighti... |
