Gas & Water Assisted Injection Mold
gas injection moulding manufacturers
gas injection moulding / gas assist injection moulding / gas assist molding
gas injection mold / gas injection mould
gas assist injection molding design guide
Water & Gas Injection Mold
Since the thermal conductivity and heat capacity of water are much bigger than nitrogen, so the injection cycle of water-assisted is about 70% shorter than the injection cycle of gas injection moulding; The product wall thickness of water-assisted injection molding is more even than gas-assisted; The inner wall roughness of water-assisted injection molding is smoother than that gas-assisted injection molding.
WATER & GAS ASSISTED INJECTION MOLDED PRODUCTS
Gas-assisted injection molding of kettle handles
What is the gas-assisted injection molding? Today we will talk about the case of gas-assisted injection molding of kettle handles. During the injection molding process, push the melt plastic to fi...
TV Frame Mold
Pushing the liquid plastic into the cavity and core side by high pressure during the injection process, and the gas pressure is maintained to form a hollow section inside the thick wall of the plastic part, the injection process is called gas-assisted injection molding.
Bike Frame Mold for Kids
During plastic molding processing, gas-assisted injection molding is abbreviated as GAIM, which is a relatively new molding processing technology, this technology is comprehensively developed on the basis of the design and manufacture of traditional injection molding molds and blow molding molds, and entered the practical stage in the 1990s, gas-assisted injection molding has huge technical application advantages and can produce significant economic benefits.
Car Ceiling Handle Injection Mould
When plastic injection molding, the melt is under the injection pressure and enters the mold cavity, on the same section, the flow rate of each gate is different, the fastest in the middle, the closer to the cavity wall, the slower the flow rate, and it contacts the cavity wall, the speed of the first layer is zero.
Water Assisted Injection Mould
Because the flow rate of the outer layer of the melt is slow and the speed of the inner layer is fast, the inner layer of melt will roll outwards and stick to the mold cavity while advancing.
Engine Coolant Pipe
In the gas-assisted injection molding process, the gas always follows the path with the least flow resistance, from high pressure to low pressure, and flows to the thick wall part, because the temperature of this part is high and the resistance is small.
Plastic Pipe Mold
The booster pressurizes the nitrogen in the low-pressure storage cylinder into workable high-pressure nitrogen, and stores it in the high-pressure nitrogen cylinder, the maximum pressure of the nitrogen can reach 35MPa in the process.
Automotive Water Intake Manifold Mould
Gas injection methods can be divided into two types, one is to inject gas together with the melt through the machine nozzle, and the other is to directly inject gas into the runner or cavity through the gas injection element (gas needle), the latter is divided into single-point intake and multi-point intake.
Gas Assisted & Water Assisted Injection Molding Differences
- Water-assisted injection moldequipment cost is nearly 10 times higher than gas-assisted injection molding, and Water assisted injection molding only can be imported currently;
- custom injection mouldingprocess is more extensive than that of water-assisted injection molding;
Gas-Assisted Injection Molding Process
Gas-assisted injection molding is roughly divided into 4 stages: plastic injection, gas injection, pressure-holding cooling, and gas discharge.
Gas-assisted injection molding classification
- gas assisted injection molded productswhich will not have sink marks or warpage, and meets the requirements of high-quality products.
As one of gas injection moulding manufacturers, we will do our best to meet all the needs of customers.
在线联系供应商
Other supplier products
 |
Medical TPE Mold | Medical TPE Mold Design is the source of a high-quality mold, one good mold design will be half success, USM uses the world's leading software to ... |
 |
Multi Cavity Mold | The runner filling balance must be considered when designing the multi-cavity mold in order to ensure the best effect of filling balance, the multi... |
 |
Automotive Water Intake Manifold Mould | Automotive Water Intake Manifold Injecting gas through the nozzle is a typical method used in rod-shaped products, because this method does not re... |
 |
4 Cavity Mold | 4 Cavity Injection Mold The multi-cavity mold can save production time, for example, one mold can produce 1 piece of part in one minute, but it ca... |
 |
Overmolding & 2k Molding | The same type of material of different colors is usually used for two-color injection molding（or 2k molding）so that the bonding strength of the fir... |
Same products
 |
steel moulds for precast concrete | 卖方: Sino Mould (Hubei) Co.,Ltd | steel moulds for precast concrete What Are Steel Moulds & Their Role for precast concre... |
 |
new jersey barrier moulds | 卖方: Sino Mould (Hubei) Co.,Ltd | new jersey barrier moulds Barrier Types & Custom Configurations Single-sided parapet bl... |
 |
culvert moulds | 卖方: Sino Mould (Hubei) Co.,Ltd | culvert moulds Structural & Configuration Types By Mold Configuration: Horizontal-type ... |
 |
manhole forming systems | 卖方: Sino Mould (Hubei) Co.,Ltd | manhole forming systems Precast Manhole/ Inlet Molds , Also called Molds for Inspection Cha... |
 |
precast concrete molds | 卖方: Sino Mould (Hubei) Co.,Ltd | precast concrete molds About Sino Mould Sino Mould is a precast concrete mould manufacturer... |
