.

Respiratory Resistance Tester

Respiratory Resistance Tester
  • Respiratory Resistance Tester
Produced by: Qinsun Instruments Co., Ltd

All supplier products
Send product request

Get a quote：

Whats/App: +86 185 0176 3615

Web: qinsun-lab.com

Respiratory Resistance Tester Introduction:

The respiratory resistance tester is used to determine the inspiratory and expiratory resistance of respirator and mask protective equipment under specified conditions. It applies to do the relevant detection and inspection for the national labor protection equipment inspection agencies, masks manufacturers of ordinary masks, dust masks, medical masks, and anti-haze masks products.

Standards:

GB 19083,
GB 2626,
GB/T 32610,
42 CFR Part 84
JIS/T 8151
EN 149,
EN 12941,
EN 14594,
NFPA 1972

Respirator Breathing Resistance TesterTechnical Parameters:
1. The instrument consists of an air source that can adjust the flow rate, a human head mold specified in the standard, two intubation systems for inhalation and exhalation, and a respiratory resistance measurement system.
2. The flow sensor has high sensitivity and has a very small starting flow.
3. The flow sensor chip uses a thermal mass flow meter, which does not require temperature and pressure compensation, ensuring high-precision measurement of the sensor. The range of the flow meter is 0 L / min ~ 100L / min, and the accuracy is ± 2%.
4. Multiple sensors are integrated on a single flow sensor chip, which greatly improves the range ratio of the sensor.
5. The zero point stability of the flow sensor is high, with full range and high stability, high accuracy with full range and excellent repeatability, low power consumption, low pressure loss and fast response speed.
6. The data logger adopts a graphic dot matrix LCD with a resolution of 128 × 64 and a full Chinese interface, which is easy to operate.
7. There is 4M memory in the data logger for measurement value recording.
8. The micromanometer sensor uses a two-wire system, with high accuracy and good stability; it is safe and reliable to use an explosion-proof design.
9. The range and zero point of the micromanometer sensor are continuously adjustable, the damping is adjustable, there is no mechanical moving part, and the maintenance workload is small. The micro-pressure measurement range is -1000Pa to 1000Pa, and the accuracy is 1Pa.
10. The whole instrument adopts special gas path conversion elements, which ensures the convenient and fast conversion of the two-pipe system of exhalation and inhalation.
11.The suction volume of the suction pump is not less than 40L / min ~ 100L / min
12. Ventilation volume is constant at (85 ± 1) L / min
13. Power supply: AC220V, 50Hz


Respiratory Resistance Test machine Feature:

▶The instrument consists of gas source that can regulates the flow, standard specifies of small human head mold, inspiratory and expiratory line system, a respiratory resistance measurement system, and so on.
▶Flow sensor has high sensitivity and minimal start flow. Flow
sensor chip uses thermal mass flowmeter, no temperature and
pressure compensation to ensure the sensor's high-precision measurement.
▶Multiple sensors are integrated on a single flow sensor chip, resulting in the sensor range greatly improved.
▶The zero stability of the flow sensor is high, with full range of high stability, with full range of high accuracy and excellent in repeatability, with low power consumption, low voltage loss and fast response characteristics.
▶Data recorder uses graphics dot matrix LCD with resolution of 128 × 64, entire Chinese interface, easy to operate.
▶There are 4M memory in the data recorder for record the measured value.
▶Micro-pressure gauge sensor adopts two-wire system, has high precision, good stability; And adopts anti-explosion design for safe and reliable.
▶Micro-pressure gauge sensor range, zero external continuously to adjustable, damping adjustable, no mechanical moving parts, less maintenance work.
▶Adopting special air-switching components to ensure that the two sets of inspiratory and expiratory piping system replacement is quick and easy.
▶Digital show the respiratory resistance, with zero calibration, accuracy calibration and over-range alarm function.
▶Equipped with a silent air compressor and air filter to ensure that the test environment is quiet and tidy.
▶Meeting with the latest national standards, compatible with labor and daily protective masks.

Respiratory Breath Resistance Test Machine Maintenance:
1. Do not carry it by the bottom of the control box during transportation to avoid being crushed.
2. Please wipe the electroplated part with oil to prevent rust and keep bright.
3. After the test, please wipe the machine clean, and regularly oil the active fulcrum to increase its service life and sensitivity. (The lubricating oil can be mixed with butter and a little engine oil)
4. Please wipe the panel (control box or display) with a dry cloth to prevent it from getting wet, so as not to damage the IC electronic parts.
5 Please place all fixtures and joint accessories properly, and wipe off the anti-rust oil to prevent rust.
6 After the machine is transported and placed, the foundation and the level must be fixed steadily.
7. Please input power as indicated. (Note that the phase of the input power supply must be correct, otherwise leakage will occur)
8 Ground wire Please perform ground output according to specifications to avoid danger of leakage and signal interference.
9 Do not pull out the plug during work.
10 Please operate and maintain by professional personnel. In case of major problems, please inform our maintenance department to dispatch personnel to handle it. Do not dismantle parts by yourself to avoid causing major losses.
Respiratory Resistance Tester(图1)


Send product request

To: Qinsun Instruments Co., Ltd
Your E-mail:
Message text:


Send to other suppliers

Other supplier products

taber abrasion and wear test instrument with double head
 taber abrasion and wear test instrument with double head Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com Mainly used for the wear tests of suitcases, carpets, cardboard, clothing, glass, ...
Taber Scratch Test machine
 Taber Scratch Test machine Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com Scratch tester Product Description:This type scratch tester made by Qinsun company...
Precision Fiber Microtome
 Precision Fiber Microtome Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com 标准： ASTM D2130、BS 2043、DIN 53811、ISO 137、IWSTM 24、IWTO 8-6 应用： 精密...
Automatic Wrinkle Recovery Tester
 Automatic Wrinkle Recovery Tester Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com Wrinkle Recovery Tester Testing Standards: AATCC 128, ISO 9867, ENKA 3061 App...
Flame Resistance Chamber Burning Tester For Full Face Masks
Flame Resistance Chamber Burning Tester For Full Face Masks Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com Introduction: The flame-retardant tester of medical mask is used to test the fl...
All supplier products

Same products

KL‑016A Benchtop High‑precision pH Meter
 KL‑016A Benchtop High‑precision pH Meter Seller: Kelilong Electron Co.Ltd Product Description: Large‑screen display with high resolution and precision for con...
Large Naïve VHH Library
 Large Naïve VHH Library Seller: AlpVHHs Large Naïve VHH Library VHHare single-domain antibodies derived from the variable regions o...
pH-2398 pH/EC/ORP/Temperature multi-parameter Water Quality Tester
 pH-2398 pH/EC/ORP/Temperature multi-parameter Water Quality Tester Seller: Kelilong Electron Co.,Ltd Feature Large display screen, capable of simultaneously measuring water quality pH, redox potent...
ORP-2026S Waterproof Soil ORP and Temperature Meter
 ORP-2026S Waterproof Soil ORP and Temperature Meter Seller: Kelilong Electron Co.,Ltd 范围 ORP -999～999mV Temp 0～50℃ 分辨率 ORP 1mV...
TDS-2616 Waterproof EC/TDS/Temperature Meter
 TDS-2616 Waterproof EC/TDS/Temperature Meter Seller: Kelilong Electron Co.,Ltd Range EC ～19.9mS TDS Temp 0～50℃ R...