Battery impact tester
Product introduction
The test sample cell is placed on a flat surface with a 15.8±0.2mm（5/8 in）
diameter rod placed in a cross position over the center of the sample. A 9.1kg or
10kg weight is dropped from a certain height （610mm or 1000mm） onto the
sample. cylinder
When the battery is subjected to impact test, its vertical axis should be parallel
to the plane and perpendicular to the vertical axis of the steel column. The most
axis of the square battery is perpendicular to the steel column, and the largest surface
is perpendicular to the impact direction. Each battery receives only one impact test.
The battery does not catch fire or explode.
Meet the standard
GBIT31485-2015 "Safety requirements and test methods of power Batteries for
Electric Vehicles"
GB/T31241-2022 "Safety requirements for lithium-ion batteries and battery packs
for portable electronic products.
UN383 United Nations Manual of Tests and Standards for the Transport of
Dangerous Goods
IEC62133 "Safety requirements for batteries （groups） composed of cells and for
use in portable equipment"
UL1642-2012 "Inner Battery Standard"
Main parameter
Inner box size :550x550x1440mm（W x D x H）
Equipment dimensions :660x900x1720mm（W x D x H）
Material :SUS201 stainless steel plate, thickness 1.2mm and coated with Teflon
Outer box material: 1.5mm thick cold rolled steel plate paint treatment
Observation window: 250x250mm tempered glass, transparent window with
stainless steel mesh.
Lighting device: The machine is equipped with a light inside to facilitate the
observation of the state of the tested sample.
Smoke outlet: 100mm in diameter, located at the rear of the box.
Pressure relief port: The opening size is 200x200mm, located at the back of the
box. When the sample is exploded, the pressure relief port will pop open and remove
the pressure.
Door: single door open left, door equipped with safety limit switch, side equipped
with explosion-proof chain to ensure the safety of personnel.
Ball weight: 9.1kg, 10kg, 0.1kg
Impact height :0-1000mm, commonly used test height 610 —— 25mm
Control mode: touch screen control
Displacement accuracy: 5mm soil
Impact mode: lift the falling ball to a certain height and release it. The falling
ball falls freely in the vertical direction without tilting or shaking.
Metal rod: Diameter 15.8±0.2mm steel rod
Maximum battery size :200x200x200mm
Impact surface :45# steel paint treatment, thickness 15mm
Equipment weight :270kg
Power supply :AC220V
Power :600W
Send product request
Other supplier products
 |
GMA Ultra-filtration Membrane Porometers | Based on the principle of liquid-liquid replacement method, the instrument realizes automaticdatacollection, analysis and calculation through an in... |
 |
Fiber Length Analyzer | The instrument uses a roller type fiber length analyzer, which will be arranged in a row of cotton cellulose according to a certain set of groups w... |
 |
Vibration and Abrasion Resistance Tester for Automotive Wire-to-Wire | In terms of main parameters: The vibration frequency of the vibrating table is 10Hz, the amplitude is 6.35±0.25mm, and the vibration directi... |
 |
Fabric Bursting Strength Tester | Bursting Strength Tester, to test the bursting strength of paper, woven or knitted fabrics, non-woven, fabric and board by the of hydraulic load un... |
 |
Fabric gsm round cutter | Round sampler also called round cutter which can apply in different materials quickly and accurately cut out the 100cm2 circular sample of diameter... |
Same products
 |
Air Permeability Tester STD- F8 | Seller: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | Seller: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | Seller: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | Seller: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | Seller: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
