Fabric Fiber Shedding Degree Tester (Friction)
Instrument Testing Principle
Lay the specimen flat and fix it on the holder. Make the wet abrasive attached to the friction head perform reciprocating friction movements on the specimen under the specified load for a specified number of times with a certain stroke.
Then compare it with the standard sample and visually rate the degree of fibers adhered to the abrasive to characterize the degree of fiber shedding of the specimen. It is suitable for factories, scientific research institutes, colleges and universities, import and export commodity inspection, textile testing in various provinces and cities.
Features of the Instrument
- Touch screen controller: The number of frictions can be set arbitrarily.
- Backup mechanical buttons for buttons in the touch screen: They can be used simultaneously, which is convenient and fast.
- Pneumatic holder for specimen installation: Convenient and fast.
- Equipped with a calender for adjusting the moisture content of the abrasive: The roll-off rate can be adjusted.
-
Complies with the standard: Appendix A of GB/T 40270 - 2021
Main Technical Performances
- Stroke of the friction head: (200 ± 2) mm
- Reciprocating speed: 30 times/min
- Diameter of the circular friction head: (90 ± 1) mm
- Outer diameter of the fixed clamp ring of the friction head: (120 ± 0.5) mm, inner diameter: (90 ± 0.5) mm
- Diameter of the test washer: (113 ± 0.5) mm
- Foam plastic washer: Diameter 105 mm, thickness 8 mm, unit area mass approximately 270 g/m²
- Total mass of the friction load: (595 ± 7) g
- Sandpaper: 600 - grit aluminum oxide water - washable sandpaper
- Power supply: AC 220V, 50Hz
Send product request
Other supplier products
 |
Automotive Bed Liner Strength Testing Machine | Standard ASTM D624(Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers) ISO 37(Rubber, Vulcaniz... |
 |
Strength Tester for Lead - end of Photovoltaic Modules | Standard IEC 61215-2:2016: Terrestrial Photovoltaic (PV) Modules – Test Requirements for Electrical and Mechanical Components CE Certificat... |
 |
QM Contact Coolness Tester | Content The sensation of coldness or warmth when skin touches an object is referred to as the “coldness and warmth feeling.” The fee... |
 |
KES - FB2 - L Large - scale Bending Tester | Content TheLarge Bending Tester accurately and quickly measures factors related to curvatures in small bending moments (bending hardness and recov... |
 |
Heel impact fatigue testing machine | Main uses: Heel impact fatigue testing machine is mainly used to test the continuous impact tolerance index of women's high heels, mid-heels and o... |
Same products
 |
Air Permeability Tester STD- F8 | Seller: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | Seller: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | Seller: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | Seller: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | Seller: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
