Wyzenbeek or Oscillatory Abrasion Tester-QINSUN

Product introduction:

Wyzenbeek wear resistance tester, also known as Oscillatory wear resistance tester, is used to test the wear resistance of fabrics against standard friction media or metal mesh surface friction movement, especially suitable for automotive decoration and furniture textile product. Instrument regulations American standard. There are 4 friction heads and electronic counter to control the running cycle.

Features：

Easy to control due to the precision electronic digital counter.

The protective cover provides protection and thus more safety.

Four abrasion heads to test samples simultaneously, thus greater efficiency.

Complied Standards：

ASTM D3597. ASTM D4157. CFFA-1A, FED-STD-191/5304. GM2756M, LP-463KB-06-01. LP-463KC-04-01. SAE J 948. SAE J1530. Toyota TSL 5101G 3.9.4 etc...

Working principles：

Install the long strip of sample fabric on the front and rear clamps of the friction head, and apply a certain tension force. Install the friction medium on the arc-shaped friction table to make the sample contact the friction medium and apply a certain load On the sample. The friction table swings back and forth to rub the sample, and after a certain number of frictions, evaluate the change in the breaking strength of the sample

Standard configuration：

Main machine 1set

Imported rubber pad 8pcs/pack

Imported metal mesh 4pcs/pack

Imported standard abrasive No. 10 cotton canvas (60inches X 5yards)

Power cable 1pcs

Manual 1pcs

Technical parameter：

1. Modern ergonomic design.

2. The suction device connected to the auxiliary vacuum cleaner.

3. Sealed transmission ensures quiet operation.

4. Test position: 4 heads.

5. Friction table: Curve surface-R100mm, length-400mm

6. Swing radian: 76+/-2mm.

7. Friction rate: 90+/-1/min(double friction).

8. Tension adjustment weight: 340g (tension adjustment range 8.9N-22.25N)

9. Load adjustment weight: 150g (load adjustment range 8.9N-17.8N)

10. Sample tension: 17.8N (adjustable)

11. Sample load: 13.4N (adjustable)

12. Sponge rubber pressure pad: 50X50mm(+/-1mm)

13. Instrument material: Stainless

14. Surface finishing: painting

15. Sample dimension: 245X73mm

16. Product dimension: 50X50X60 (LXWXH)

Other supplier products

	Gravel Resistant Impact Tester/Stone chip tester	Standards ASTM D3170: Coating resistance to gravel impingement. ISO 20567: Paints and varnishes – Resistance to stone chipping. SAE J400...
	Geomembrane thickness tester	Scope of application: Used to determine the thickness of smooth geomembrane and other plastic films under specified pressure and time. The sample ...
	KES - QM Contact Coolness Tester	It is used to measure and evaluate the contact coolness index "q max" (peak heat flux). When the skin comes into contact with fabrics, different am...
	Car seat headrest insertion and withdrawal force durability tester	Applicable standards: GB 11550-2009 "Automobile seat headrest strength requirements and test methods" : This standard specifies the test methods...
	Geomembrane Hydrostatic and Permeability Tester-QINSUN	Scope of application: It is used to test the hydrostatic pressure resistance and permeability coefficient of nonwoven composite geotextile （one cl...

All supplier products

Same products

	Air Permeability Tester STD- F8	Seller: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...
	Surface Performance Tester STD-FB4 - A	Seller: Standard International Group (HK) Limited	Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti...
	Compression Tester STD - FB3 - A	Seller: Standard International Group (HK) Limited	TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar...
	Single - Strand Bending Tester STD - FB2 - SH	Seller: Standard International Group (HK) Limited	Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ...
	Bending Tester STD- FB2 - S	Seller: Standard International Group (HK) Limited	Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig...