Resistance Tester for Molten Metal Droplet (Splash) Impact Performance
Performance and Standards:
This resistance tester for molten metal droplet (splash) impact performance is developed in accordance with testing standards such as ISO 9150. EN 348. GB/T 17599. AQ6103. GB 8965.2. etc. It is applicable to the protective performance of various fabrics and composite fabrics against burns caused by molten metal splashes on the human body. Its testing principle is to determine the number of molten droplets required for the temperature rise of 40K behind the sensor when metal droplets impact the specimen at a certain angle.
Technical Parameters
Oxygen and acetylene flow regulation devices, which can provide standard gas flow for welding nozzles.
Oxygen and acetylene pressure regulation devices, which can precisely control the inlet pressure to 250Kpa and 50Kpa.
Oxyacetylene welding torch for melting metal strips, with a welding nozzle diameter of (1.2 ± 0.1) mm.
A stepper motor is used to drive the metal strip, and the running speed of the metal strip can be set.
Droplet guiding mechanism, equipped with a high-temperature anti-sticking guide groove, with an angle of 45 degrees.
Fabric temperature measurement sensor device, including a refractory insulating rock wool support block and an armored platinum resistance thermometer, for measuring the temperature rise on the back of the specimen.
Counterweight copper hammer device, used to set a pre-tension of 175g ± 0.5g for the fabric.
A droplet counting device is provided, which can display the number and frequency of droplets during the test.
Equipped with standard testing software for resistance to molten metal splash impact performance, with a touch screen human-machine interface control, which can display test parameters such as temperature rise curves.
The whole machine is equipped with a protective cover to protect the safety of testers.
Send product request
Other supplier products
 |
Bone Plates Static Four - point Bending Tester | Standard YY/T 0342-2022: Chinese standard specifying methods for determining bending strength and equivalent bending stiffness of straight and pre... |
 |
Sharp edge tester | Standards : ASTM F963 4.8. EN71-1998 8.14. GB6675-2003 A.5.9. 16CFR 1500.48 Basic Configuration： Sharp Edge Tester: 1 unit Foot switch: 1 set ... |
 |
Total Knee Joint Prostheses Wear Tester | Standard ISO 14243-1:2014: Specifies wear testing parameters for total knee prostheses, including axial loading, flexion/extension kinematics, and... |
 |
IP6X IP5X Ingress Test Chamber | Features and Benefits 1.Vertical circulation air blows dust to the workroom, forming a dust circulation system, dust can be recycled 2.Different ... |
 |
Syringe slide performance tester | The Syringe Slide Performance Tester is a specialized instrument designed to measure the push and pull forces of syringe plungers, ensuring smooth ... |
Same products
 |
Air Permeability Tester STD- F8 | Seller: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | Seller: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | Seller: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | Seller: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | Seller: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
