UV Sterilizer
Product introduction of Environmental test chamber
Ultraviolet disinfection technology is the latest generation of disinfection technology emerging in the late 1990s. It integrates optics, microbiology, electronics, fluid mechanics, and aerodynamics. It has the characteristics of high efficiency, broad spectrum, low cost, long life, large water volume, and no secondary pollution. It is internationally recognized in the 21st century. Mainstream consumer technology.
Advantages of UV disinfection technology
The disinfection effect of ultraviolet C disinfection technology on bacterial viruses and other pathogens has been recognized worldwide, and it has unparalleled bactericidal efficiency. The germicidal effect of ultraviolet rays on bacteria and viruses is generally within one second. For traditional chlorine and ozone methods, it takes 20 to 50 minutes to achieve the sterilization effect of ultraviolet rays. It has a broad spectrum of efficient sterilization, no secondary pollution, safe and reasonable design, safe and reliable operation. Simple maintenance and low cost. This equipment occupies a small area and has no noise. Continuous mass sterilization. Wide application fields and many other advantages
Product parameters
1. Total equipment length: 2000mm
2. Working area length: 1000mm
3. Feeding operation area: 500mm Discharging operation area: 500mm
4. Height of entrance and exit: 200mm
5. Conveyor width: 500mm
6. Conveyor belt from the ground: 750 ± 20mm
7. A total of 16 lamps are installed in the sterilizer, each power: 20W)
Product main configuration and structure
1. Work area tunnel body:high-quality 304 screen stainless steel
2. Working area tunnel cavity: mirror stainless steel Model: # 304
3. Body support frame: one set of Fangtong Steel Model: 2 ″ Fangtong
4. Air transport system: a set of forced air transport exhaust fans (extracting harmful gas) Model: 6 inches
5. Thermal insulation material: Vacuum aluminum silicate + silk cotton double layer Model: 60K
6. Conveyor belt: Teflon mesh belt 1. Main switch: 20A
7. Transport motor: 800W (inverter speed regulation)
8. Speed governor: 500W (electronic stepless inverter speed regulation digital display speed operation)
9.Exhaust fan: CY-125
10. Ammeter: 50A set
11.Voltmeter: 220V one set
12. Working voltage: 200V--220V (± 5) Three-wire system 50Hz
Effective light moment of ultraviolet light source: 150mm
Tube length 460mm
16 UV germicidal lamp tubes * 20W UV lamps are located in the inner cavity longitudinally, and are installed on the top, bottom, left and right
The wavelength is 253.7nm, and the radiation intensity at a distance of 1 meter is more than 160 microwatts per square centimeter. Life is 8000 small
Send product request
Other supplier products
 |
Contact heat transmission test machine | Introduction: This part of ISO 12127 specifies a test method designed to evaluate the heat transfer and the behaviour ofmaterials used for prote... |
 |
Dry Sand Rubber Wheel Abrasion Tester | Standard ASTM G65 JBT_7705 Applicable standards Dry and wet abrasive wear testing machines usually need to follow certain standards and specifi... |
 |
Electrostatic Decay Tester | The Electrostatic Decay Tester is professionally designed to evaluate the static electricity attenuation characteristics of textile and non-textile... |
 |
Safety Helmets Against Molten Metal Splashing Tester | Standard GB/T 2812-XXXX: Safety Helmets – Test Methods for Molten Metal Resistance (Draft Standard) GB 2811-2019: Head Protection – G... |
 |
Helmet Surface Friction Testing Machine | Purpose The Helmet Surface Friction Tester presses a helmet onto a movable fixture with a certain force. The surface of the fixture is attached wi... |
Same products
 |
Gas Oxidizing Property Tester | Seller: Standard International Group (HK) Limited | Product Description Conforms to ISO 10156-2010 “Gases and Gas Mixtures Selection of Cylind... |
 |
Battery Powder Compaction Density Measurement System | Seller: Standard International Group (HK) Limited | The Battery Powder Compaction Density Measurement System is a precision testing system designed... |
 |
Battery Powder resistance tester | Seller: Standard International Group (HK) Limited | The Powder Resistivity Meter is a precision testing system designed to measure electrical resisti... |
 |
KES-SESRU surface roughness/friction tester | Seller: Standard International Group (HK) Limited | TheRoughness/Friction Tester analyzes hand movements-particularly, strokes-performed by artisans ... |
 |
Air Permeability Tester STD- F8 | Seller: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
