.

Vertical Low Damping Hard Track Machining Center

The hard-rail low-damping vertical machining center is suitable for large and medium-sized mold processing. Its Y-axis stroke can reach 700mm. The three-axis transmission mode——direct transmission,Website:, large axial thrust, wide base and four-track support structure.All castings are cast from Meehan material. After casting, the parts are annealed. The surface of the guide rail is quenched and heat treated and precision ground. The contact surface of the slide has wear-resistant fluorinated resin (RULONAR) with low damping and low friction coefficient. And other characteristics.(1) The cooling system and the oil cooler cool the machining and cutting spindles;(2) Lubricate the transmissions by the lubrication system to reduce the friction resistance and increase the service life of the machine;(3) It can be equipped with a dedicated chip conveyor for concentrated chip removal;(4) It can be equipped with a tool magazine to implement automatic tool change, saving time for tool change;(5) Horizontal (fourth axis) motion can be achieved with the fourth axis and the rotary table.Characteristics1. Environmental protection and no pollution. Because there will be no oil and mist sprayed out, the surrounding environment will not be contaminated.2. The oil supply is accurate. By adding a regulating valve, the oil can be delivered to the lubrication points such as the spindle and the screw according to different needs;3. There is no problem of difficulty in atomization of high viscosity lubricating oil; suitable for any oil product;4. Automatic detection and monitoring. It can detect whether the lubricating oil is normal. If the lubrication is poor, it can stop the alarm and avoid the abnormal operation of the equipment.5. It is especially suitable for the rolling bearing of the main shaft. It has a certain air cooling effect, which can reduce the operating temperature of the bearing and thus prolong the service life of the main shaft.6. Low fuel consumption and cost saving.



Send product request

To: Shenzhen Ze'anfu Hardware Electronic Technology Co., Ltd.
Your E-mail:
Message text:


Send to other suppliers

Other supplier products

Vertical Low Damping Hard Track Machining Center
Vertical Low Damping Hard Track Machining Center The hard-rail low-damping vertical machining center is suitable for large and medium-sized mold processing. Its Y-axis stroke can reach 700mm. The ...
Vertical High-speed Hard-track Machining Center
Vertical High-speed Hard-track Machining Center Structural features:A high-speed machining center for mold processing, a common structural feature is the use of a gantry frame structure to enhanc...
Vertical High Precision Wire Processing Center
Vertical High Precision Wire Processing Center Advantage:1. Optional disc manipulator and bucket type tool magazine, featuring high precision, high efficiency, stable tool change, long-lasting d...
Vertical High Speed Machining Center
Vertical High Speed Machining Center Advantages of vertical high speed machining center:1. High processing speed of ultra-high speed machining center2, the cutting force of the ultra-h...
Vertical Low Speed Linkage Machining Center
Vertical Low Speed Linkage Machining Center The vertical machining center is mainly used for processing complex parts such as plates, plates, molds and small shells. Vertical machining center...
All supplier products

Same products

Vertical High Speed Machining Center
Vertical High Speed Machining Center Seller: Shenzhen Ze'anfu Hardware Electronic Technology Co., Ltd. Advantages of vertical high speed machining center:1. High processing speed of ultra-high speed m...
Vertical High-speed Hard-track Machining Center
Vertical High-speed Hard-track Machining Center Seller: Shenzhen Ze'anfu Hardware Electronic Technology Co., Ltd. Structural features:A high-speed machining center for mold processing, a common structural featur...
Vertical Low Speed Linkage Machining Center
Vertical Low Speed Linkage Machining Center Seller: Shenzhen Ze'anfu Hardware Electronic Technology Co., Ltd. The vertical machining center is mainly used for processing complex parts such as plates, plates,...
Vertical High Precision Wire Processing Center
Vertical High Precision Wire Processing Center Seller: Shenzhen Ze'anfu Hardware Electronic Technology Co., Ltd. Advantage:1. Optional disc manipulator and bucket type tool magazine, featuring high precision, h...
Vertical Low Damping Hard Track Machining Center
Vertical Low Damping Hard Track Machining Center Seller: Shenzhen Ze'anfu Hardware Electronic Technology Co., Ltd. The hard-rail low-damping vertical machining center is suitable for large and medium-sized mold p...