Adjustable Applicator

BEVS1806 Adjustable Film Applicator is designed based on ASTM D 823 E with two built-in metric micrometer heads for adjusting the knife blade so that clearances of the blade can be accurately set from 0-10mm in 0.01mm increments.

The applicator consists of:

• A special anodized aluminum frame to guide the knife blade. The frame has two end

sections which serve as hand grips for the operator when drawing down wet films.

• A STAINLESS STEEL knife blade with a precision ground edge. The slides in slots in the

end sections which allows vertical adjustments of the blade.

• Two springs attached to the knife-blade and top plate. These exert an upward pressure on

the blade and maintain it in contact against the two micrometer spindles to retain gap

settings of the blade.

• Two precision made micrometer heads that can easily be set to give film thickness from

0-10mm in increments of 10 microns. The accuracy of the micrometer heads is ± 2 microns.

• Imperial micrometer heads are available if required.

• Complies with ASTM D 823 Practice E

Specification:

BEVS1806/50/100/150/200/250/300 Film Width:50/100/150/200/250/300mm Accuracy:±2um

Film Thickness Range: 0-10mm in increments of 10 microns.

Wet films of uniform thickness can be produced with the knife blade set for the desired

2. Place applicator at upper end of test panel.
3. Pour coating sample directly in front of knife-blade.

Before use check the zero settings of the micrometer heads as follows:

1,Place applicator on a polished plate glass of suitable size. Set micrometer heads to zero.

2,When the applicator is placed between the observer and a bright light the blade should touchthe glass from end to end and not lift the end section. The zero point should check within±1,division of the micrometer - this is set at manufacture.

If applicator does not zero and resettings are required proceed as follows:

Set the micrometer heads to zero, loosen the micrometer clamp set screws, press the knifeblade down onto the glass plate, press down the micrometer heads until their spindles are

contacting the blade and then tighten the micrometer clamp screws.

6. There will have the film error as the knifeblade appears crack and transformation by the falling and crash. So take good care of the equipment when it is in process of use.
7. Screw is not allowed to tear down as the calibration was already finished before delivery. Or it will have the error.

6 order information

BEVS 1806/50 Adjustable Applicator 50mm Width

BEVS 1806/100 Adjustable Applicator 100mm Width

BEVS 1806/150 Adjustable Applicator 150mm Width

BEVS 1806/200 Adjustable Applicator 200mm Width

BEVS 1806/250 Adjustable Applicator 250mm Width

BEVS 1806/300 Adjustable Applicator 300mm Width

Other supplier products

	BEVS 2501 Lab Mixer	Introduction:BEVS 2501 series Laboratory Mixer adopts frequency-adapter to adjust speed with the advanced touch-screen control design. Enable to di...
	BEVS 2203 Multi-hatch Gauge
	Automatic Cupping Tester	BEVS Automatic Cupping Tester is a advance technology to efficiently assess the elasticity and cupping resistance of various coatings, with a new g...
	BEVS 2805 Wet Abrasion Scrub Tester	Introduction: This machine is used to test the abrasion, scrub and washability performance for many kinds of materials, do the abrasion scrub test ...
	BEVS 1112 Intelligent Krebs Viscometer	BEVS1112 is a advanced touch screen control automatic viscometer of leading industry, the most suitable for measuring the non-newtonian fluid such ...

All supplier products

Same products

	Reliable Components for Water and Industrial Systems	Seller: 866507	The Stainless Steel Float Ball is designed for automatic liquid level control and fluid managem...
	Double Convex Lenses	Seller: Shandong Yanggu Constant Crystal Optics, Inc	Double Convex Lensesare used in image relay applications, or for imaging objects at close conjuga...
	Wedge Prism	Seller: Shandong Yanggu Constant Crystal Optics, Inc	Wedge prismis an optical element with plane-inclined surfaces, usually the faces are inclined tow...
	Ball Lenses	Seller: Shandong Yanggu Constant Crystal Optics, Inc	Ball Lensesare commonly used to improve signal quality in fiber coupling applications, or for use...
	KAZUKI 6-GFM-33 12V33Ah AGM Gel Battery	Seller: Xin Tang Shallow Power Supply Co.,LTD	KAZUKI 6-GFM-33 12V33Ah AGM Gel Battery Small Office & Retail UPS Backup Power Systems...