Adjustable Applicator

BEVS1806 Adjustable Film Applicator is designed based on ASTM D 823 E with two built-in metric micrometer heads for adjusting the knife blade so that clearances of the blade can be accurately set from 0-10mm in 0.01mm increments.

The applicator consists of:

• A special anodized aluminum frame to guide the knife blade. The frame has two end

sections which serve as hand grips for the operator when drawing down wet films.

• A STAINLESS STEEL knife blade with a precision ground edge. The slides in slots in the

end sections which allows vertical adjustments of the blade.

• Two springs attached to the knife-blade and top plate. These exert an upward pressure on

the blade and maintain it in contact against the two micrometer spindles to retain gap

settings of the blade.

• Two precision made micrometer heads that can easily be set to give film thickness from

0-10mm in increments of 10 microns. The accuracy of the micrometer heads is ± 2 microns.

• Imperial micrometer heads are available if required.

• Complies with ASTM D 823 Practice E

Specification:

BEVS1806/50/100/150/200/250/300 Film Width:50/100/150/200/250/300mm Accuracy:±2um

Film Thickness Range: 0-10mm in increments of 10 microns.

Wet films of uniform thickness can be produced with the knife blade set for the desired

2. Place applicator at upper end of test panel.
3. Pour coating sample directly in front of knife-blade.

Before use check the zero settings of the micrometer heads as follows:

1,Place applicator on a polished plate glass of suitable size. Set micrometer heads to zero.

2,When the applicator is placed between the observer and a bright light the blade should touchthe glass from end to end and not lift the end section. The zero point should check within±1,division of the micrometer - this is set at manufacture.

If applicator does not zero and resettings are required proceed as follows:

Set the micrometer heads to zero, loosen the micrometer clamp set screws, press the knifeblade down onto the glass plate, press down the micrometer heads until their spindles are

contacting the blade and then tighten the micrometer clamp screws.

6. There will have the film error as the knifeblade appears crack and transformation by the falling and crash. So take good care of the equipment when it is in process of use.
7. Screw is not allowed to tear down as the calibration was already finished before delivery. Or it will have the error.

6 order information

BEVS 1806/50 Adjustable Applicator 50mm Width

BEVS 1806/100 Adjustable Applicator 100mm Width

BEVS 1806/150 Adjustable Applicator 150mm Width

BEVS 1806/200 Adjustable Applicator 200mm Width

BEVS 1806/250 Adjustable Applicator 250mm Width

BEVS 1806/300 Adjustable Applicator 300mm Width

Other supplier products

	BEVS 1802 Two Sided Applicator	The coating with excellentconsistency and repeatability is required when doing the coating opacity, wear-resistance, sag-resistance performance and...
	BEVS 1815 Drying Time Recorder	BEVS Drying Time Recorder is used for the test of drying time or gel behavior of a variety of paints and coatings. It has the characteristics of in...
	BEVS 1011	Introduction: It is designed according to ASTM D1200, D333 and D365 standards and widely used to measure the viscosity of paints,inks, lacquers and...
	Cylindrical Mandrel Bend Tester	INTRO. A very robust mechanical unit for determining the elasticity, adhesion and elongation of dried paint on sheet metal. It can be used in accor...
	杯凸仪	BEVS Automatic Cupping Tester is a advance technology to efficiently assess the elasticity and cupping resistance of various coatings, with a new g...

供应产品

Same products

	Battery Powder Compaction Density Evaluation System	卖方: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application (1) Measurement of tapped de...
	Lingfeng (LF) Air-Cooled Integrated Refrigeration Chillers	卖方: Beijing Linggong Technology Co., Ltd.	TheLingfeng(LF)Air-Cooled IntegratedRefrigerationChillersis a professional refrigeration equipmen...
	Low Temperature Chiller	卖方: Beijing Linggong Technology Co., Ltd.	Low Temperature Chiller The conditioning deviceis specifically designed for thermal and fluid dy...
	Low-Temperature Control System	卖方: Beijing Linggong Technology Co., Ltd.	Low-Temperature Control System The conditioning deviceis specifically designed for thermal and f...
	Plastic Smoke Density Tester F313	卖方: Standard International Group (HK) Limited	The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ...