IEC 60695-2-20 Hot Wire Ignition Test Apparatus
IEC 60695-2-20 Hot Wire Ignition Test Apparatus Hot wire ignition tester is according to the standard requirement of IEC60695-2-20 and GB4943,Website:, which meets Standard Test Method for Ignition of Materials by Hot Wire Sources. It is suitable for electric and electronic products, household appliance materials to do ignition dangerous test. It simulates the heat source or ignition source of simulates glow component and overload resistance which may cause thermal stress in a short time.Hot-wire coil ignition test adopts the specific size (Dia: 0.5mm; Length: 250mm) and specific material (Ni80/Cr20) of heater strip which is pre-annealed with required heating power (0.26W/mm) and specified time (8s~12s). Then coil heater strip on the specimen for 5 cycles according to certain wire wrapping tension (5.4N) and certain wire wrapping distance (6.35mm). Then take the specimen with wrapping heater strip to test until 120s under the stipulate heating power (0.26W/mm) the users can judge the fire risk according to whether the specimen ignite and the ignite time.Specification:
• It is according to IEC60695-2-20 and GB4943
• Heating coil: ф0.5mm, Ni80/Cr20, Length: 250mm±5mm , Cold Resistance: 5.28Ω/m , Anneal holder distance: 250mm
• Specimen holder distance and height: 70mm, Height: 60mm (The distance from stand surface to the connector plate surface)
• Wire wrapping tension and its distance: 5.4N±0.05N, 6.3mm±0.2mm (within 31.5mm±0.5mm, coil 5 cycle, national standard is 6mm)
• Annealing time and power: 8s~12s (Digital display can be preset). 0.26W/mm±4%( Digital display is adjustable)
• Testing time and power 120s ( 1s~999.9s Digital display can be preset),0.26W/mm±4%(Digital display is adjustable)
• Specimen size: L×W×H: (125±5)×(13.0±0.5)×(0.75+0.075)mm,1.5+0.150mm,3+0.3 0mm) national standard 0.75±0.1 mm, 1.5±0.1 mm, 3±0.2 mm
• Combustion box volume is bigger than 0.5 cubes(other size can be option)
Other supplier products
|
|
IEC 60695-2-2 IEC 60695-11-5 Needle Flame Test Apparatus With 45° Burner |
IEC 60695-2-2 IEC 60695-11-5 Needle Flame Test Apparatus With 45° Burner According to IEC60695-2-2 and IEC60695-11-5,Website:, ZY-3 Needle Flame Te... |
|
|
LED Power Driver Test Equipment |
LED Power Driver Test Equipment WT2080 LED Power Driver Test Equipment is the comprehensive test instrument for LED drive power which is according ... |
|
|
IEC 60068-2-52, ASTM-B368, MIL-STD-202, EIA-364-26, ASTM-B117 Salt Spray Test Chamber |
IEC 60068-2-52,Website:, ASTM-B368, MIL-STD-202, EIA-364-26, ASTM-B117 Salt Spray Test Chamber The Salt Spray Test Chamber is applicable to the sal... |
|
|
Integrating Sphere Theory For Lighting Test |
Integrating Sphere Theory for Lighting Test Due to the LED luminaries such as LED street luminaries developed,Website:, to do 4π geometry testing, ... |
|
|
LM-79 Moving Detector Type C Goniophotometer |
LM-79 Moving Detector Type C Goniophotometer LSG-1900 Moving Detector Type C Goniophotometer completely meets LM-79 Clause 9.3.1 requirement. The L... |
All supplier products
Same products
