Friction Charging Tester

• 

Standards compliant:
JIS L-1094;
JIS T-8118;
ZB W 04008-89;
GB / T12703.2-2009;
GB 12014-2009;
GB / T23316-2009

Calculation formula:
Q = CV / A
Here, C: the charge amount of the capacitor (F) = 0.1 × 10-6 (F)
V: Voltage reading of potentiometer (V)
A: friction area of ​​sample (m2) = 0.25 × 0.25 (m2)

Steps:
1, connecting the Faraday tube and the amount of charge measurement device: the end of a dedicated cable connected with the input of the charge meter connected to the other end of the Faraday tube with the outer cylinder of the socket connection.
2, turn on the charge amount of the tester power - the power switch up to the "1" position.
3, press the "clear" button, so that the charge meter shows the number is zero.
4, with a roller friction machine friction test, immediately after the end of the friction with the insulation rods into the Faraday tube tube inside the tube. In this process the specimen and other objects should be kept above 300mm.
5. Read the reading on the charge quantity measuring device.

Friction Charging TesterNote:

• 1, the system of Faraday tube outer cylinder should be reliably grounded.
• 2. Clear the charge amount measurement unit before each measurement.
• 3, the measured object must be measured from the power supply.
• 4, before the test, please turn on the power switch to make the machine warm up for 15 minutes.
• 5, voltage / current generator is not to sell goods.

• Fabric Friction Charging Charge Tester:

  Voltage meter (R8240): 1 set
  Capacitor: 1 set
  Cable (A01009-200): 1 root
  Connection cable (A01009-50): 1 root
  Power supply-type strip in addition to the electrode: 1 root
  Friction abutment / ground pad (nylon friction cloth): 1 set
  Insulated rods (20Φ x 500L mm acrylic clear fiber): 1 root
  Certificate of proof of voltage meter (traceability): 1 book

Other supplier products

	Tibial Tray Fatigue meter	YY/T 0810 (China): Specifies fatigue testing protocols for tibial trays in total knee arthroplasty, focusing on support and protection of plastic b...
	Heel Fatigue Tester	Heel Fatigue Tester is used to determine the resistance of medium and high heels of ladies’ shoes under repeated small impacts to the heel ti...
	Single Burning Item	Introduction Single burning instrument (SBI) was measured supplies (excluding floorings) performance at a single burning heat invasion conditions....
	Shoelace wear tester	Main uses: Shoelace wear tester is mainly used to evaluate the durability and wear resistance of shoelaces. In the test, the LACES are usually fix...
	FPC Flex Durability Test device	Standard ASTM F392 Product features 1. the stepper motor drive, high-precision positioning, low noise, can be used for a long time 2. program-c...

Same products

	Plastic Smoke Density Tester F313	Seller: Standard International Group (HK) Limited	The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ...
	WYLIE WL-155 SIM Card Tester for iPhone 14-17 Pro Max & Android	Seller: China PHONEFIX Technology Co., Ltd	WYLIE WL-155 SIM Card Tester is used to detect SIM card circuits and supports dual-SIM detection ...
	HCV1500 High-precision Voltage Sensor	Seller: Shenzhen Hangzhi Precision Electronics Co., Ltd	HCV1500 high-precision voltage sensor is a voltage sensor that can measure DC, AC, pulse and vari...
	Xenon Test Chamber	Seller: Standard International Group (HK) Limited	Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli...
	Single Cable Vertical Flame Tester	Seller: Qinsun Instruments Co., LTD	Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ...