Resistance Tester for Molten Metal Droplet (Splash) Impact Performance/ISO 9150/AQ6103
Product Information:
This resistance tester for molten metal droplet (splash) impact performance is developed in accordance with testing standards such as ISO 9150. EN 348. GB/T 17599. AQ6103. GB 8965.2. etc. It is applicable to the protective performance of various fabrics and composite fabrics against burns caused by molten metal splashes on the human body. Its testing principle is to determine the number of molten droplets required for the temperature rise of 40K behind the sensor when metal droplets impact the specimen at a certain angle.
Oxygen and acetylene flow regulation devices, which can provide standard gas flow for welding nozzles.
Oxygen and acetylene pressure regulation devices, which can precisely control the inlet pressure to 250Kpa and 50Kpa.
Oxyacetylene welding torch for melting metal strips, with a welding nozzle diameter of (1.2 ± 0.1) mm.
A stepper motor is used to drive the metal strip, and the running speed of the metal strip can be set.
Droplet guiding mechanism, equipped with a high-temperature anti-sticking guide groove, with an angle of 45 degrees.
Fabric temperature measurement sensor device, including a refractory insulating rock wool support block and an armored platinum resistance thermometer, for measuring the temperature rise on the back of the specimen.
Counterweight copper hammer device, used to set a pre-tension of 175g ± 0.5g for the fabric.
A droplet counting device is provided, which can display the number and frequency of droplets during the test.
Equipped with standard testing software for resistance to molten metal splash impact performance, with a touch screen human-machine interface control, which can display test parameters such as temperature rise curves.
The whole machine is equipped with a protective cover to protect the safety of testers.
Standards:
ISO 9150. EN 348. GB/T 17599. AQ6103. GB 8965.2. etc.
Send product request
Other supplier products
 |
Total Hip Joint Prostheses Wear Tester | Standard YY/T 0651.1-2016 (China): Specifies wear testing parameters for total hip prostheses, including angular motion, loading modes, and envi... |
 |
Intervertebral Fusion Cages Torsion Fatigue Tester | Standard YY/T 0959-2014 (China): Specifies torsional fatigue testing protocols for intervertebral fusion devices, including load ratios, frequen... |
 |
Zipper Comprehensive Strength Testing Machine | Meet the standard: ASTM D2061 ASTM D2060 BS 3084 JIS S3015 DIN 3419 Product Introduction: The mechanical strength of a zipper's components i... |
 |
Coatings Shear Fatigue Tester | Standard YY/T 0988.13-2017 (China): Specifies shear fatigue testing protocols for coatings on metallic substrates, including load ratios, freque... |
 |
Liquid Spontaneous ignition point tester | Product Description complies with GB/T 21860-2008 “Test Method for Autoignition Temperature of Liquid Chemicals” and ASTM E “Tes... |
Same products
 |
Plastic Smoke Density Tester F313 | Seller: Standard International Group (HK) Limited | The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ... |
 |
Xenon Test Chamber | Seller: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | Seller: Qinsun Instruments Co., LTD | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | Seller: Qinsun Instruments Co., LTD | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | Seller: Qinsun Instruments Co., LTD | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
