Falling Sand Abrasion Tester
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Applicable Standard
JG/T 133-2000
ASTM D968-83
ASTMD333
ASTMD1395
ASTMD2205
Main Purposes
It is mainly used to test the abrasion - resistance of the lenses of helmet goggles and evaluate their ability to resist particle - induced damage.
Instructions For Use
1. according to the standard requirements for the preparation of test plates and placed in (23 +-2) degrees Celsius, relative humidity (50 +-5) degrees Celsius conditions for 24 hours.
2. Calibrate the apparatus:
Pour a certain amount of sand into the funnel, check the sand stream falling from the lower end of the conduit, and calibrate the device with the bottom adjusting screw until the inner part of the sand beam falls exactly on the center of the sand stream when viewed from two positions of 90 degrees Celsius each other. Use the high and low adjusting nut to adjust the distance from the tube tube to the painted surface according to the ASTM standard, when measured in the vertical direction, the near point of 1 inch (25mm), the user needs to be adjusted according to the thickness of their own samples, factory machine pre-adjustment of 25mm. to the pouring of a certain volume amount of sand (to 2000 +-10ml is appropriate), and measure the outflow time, the outflow rate should be 21S- 23.5S within 2L. This speed comes from the ASTM standard, and with the international standard sand for the test, we measured the speed of 1 minute 7L or more.
3. do the test should pay attention to, after the end of the sand fall, the machine should be slightly tilted to make the lower funnel in the small square of excess sand poured out, in the re-insertion of the sand fall switch in order to avoid the sand fall switch can not be put in.
Main Technical Parameters
Overall Dimension: 230mm×200mm×1500mm (L×W×H)
Catheter Length: 36 inches (914mm)
Catheter I.D.: 0.75 inches (19mm)
Hopper Volume: 3L
Machine Weight: 25KG
Send product request
Other supplier products
 |
Safety Footwear Compression Puncture Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Test purpose Measure the compression resistance of the shoe head cover and the puncture re... |
 |
Waterproof socks testing machine | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Waterproof Socks Testing Machine is designed to evaluate the water resistance and water... |
 |
Guide pin anchoring force tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Guide Pin Anchoring Force Tester is designed to evaluate the anchoring performance of m... |
 |
Battery combustion tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Battery Combustion Tester is designed for safety evaluation of lithium-ion batteries by... |
 |
Vertical Computer Control Universal Friction And Wear Testing Machine | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application (1) Research and development in tribology and material sciences. (2) Friction... |
Same products
 |
FH-77 Dissolved hydrogen meter | Seller: Kelilong Electron Co.,Ltd | Pen type dissolved hydrogen detector / dissolved hydrogen meter: used to measure the dissolved hy... |
 |
Xenon Arc Weather Ometer | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App: +86 181 0160 0864 SI4000Xenon Arc Weather Ometer utilizes a xenon lamp ... |
 |
Xenotest | Light Fastness Tester Si220 (SunTest) | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App:+86 180 0160 0864 A Light Fastness Tester, or Xenon Tester, Accelerated ... |
 |
Ozone Aging Chamber | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App:+86 156 1874 6768 The Ozone Aging Chamber is a precision testing instrum... |
 |
Plastic Smoke Density Tester F313 | Seller: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com The F313 Plastic Smoke Density Tester is ... |
