Rubber hose outer coating wear testing machine
Product Introduction:
Rubber hose outer coating Wear testing machine for hydraulic hoses and other similar types of hoses with fabric or steel wire reinforced outer coating with a smooth and flat surface.
Test method:
1. Install the assembled sample and mandrel on the test device, and ensure that the sample has no axial movement and (or) rotation.
2. place the abrasive tool to make contact with the sample, apply the vertical static pressure F specified in the product standard, and start the machine. If the force F is not specified in the product standard, the applied vertical static pressure should be 50N±0.5N.
3. the test is carried out until the specified number of cycles is completed, and then the sample assembly is removed from the test device, and the sample with or without a core shaft is weighed again as the initial weighing. It is important to remove any particles attached to the outer coating before weighing.
Test standard:
GB/T 12721-2007 - Determination of abrasion resistance of rubber hose outer coating
ISO 6945:1991 - Determination of the abrasion resistance of rubber hose cladding
KS M ISO 6945-2013 - Determination of the abrasion resistance of the outer coating of rubber hoses
EN ISO 6945-1996 - Determination of the abrasion resistance of rubber hose outer coatings
DS/ISO 6945-1984 Determination of wear resistance of rubber hose cladding
Main parameters:
1. reciprocating frequency: 1.25Hz(45 RPM)
2. cycle stroke: 200mm
3. loading static pressure: 50N±0.5N(other pressure weights can be customized processing)
4. Mandrel length: 150mm
5. shaft diameter: 5mm, 8mm, 10mm, 13mm, 16mm, 19mm, 22mm, 25mm, 32mm, 38mm, 45mm, 51mm, optional three, can also provide dimensional processing
Send product request
Other supplier products
 |
Vacuum Ball - Disk Friction Tester | Standards ASTMD4172-94 ASTMD2266-91 SH/T0189-92 Main Purposes The vacuum ball - disk friction tester is a device specifically used for evaluat... |
 |
Absorbable Bone - connecting Plates Four - point Bending Tester | Standard ASTM F2119: Standard test method for constant load testing of bioabsorbable screws and washers, applicable to bending performance evalu... |
 |
Gurley Stiffness Tester STD-AG84 | Application The Gurley Stiffness Testeris based on the Gurley Softness Tester test method. It applies a certain mechanical external force to the s... |
 |
Motorcycle Helmet Sand Drop Tester | Main application Helmet abrasion resistance sand test machine is mainly used to test motorcycle helmets, sports helmets, electric vehicle helmets,... |
 |
Automatic Wrinkle Recovery Tester | The main principle of the wrinkle recovery tester is to apply a predetermined pressure to the specimen under standard atmospheric conditions and to... |
Same products
 |
FH-77 Dissolved hydrogen meter | Seller: Kelilong Electron Co.,Ltd | Pen type dissolved hydrogen detector / dissolved hydrogen meter: used to measure the dissolved hy... |
 |
Xenon Arc Weather Ometer | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App: +86 181 0160 0864 SI4000Xenon Arc Weather Ometer utilizes a xenon lamp ... |
 |
Xenotest | Light Fastness Tester Si220 (SunTest) | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App:+86 180 0160 0864 A Light Fastness Tester, or Xenon Tester, Accelerated ... |
 |
Ozone Aging Chamber | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App:+86 156 1874 6768 The Ozone Aging Chamber is a precision testing instrum... |
 |
Plastic Smoke Density Tester F313 | Seller: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com The F313 Plastic Smoke Density Tester is ... |
