Button Impact Machine
Standards:
ASTM D5171: Test Method for Abrasion Resistance of Inks and Coatings (referenced for impact-related durability assessments).
Application:
Button falling weight impact testeris used to determine the impact resistance of plastic sew-through flange buttons to a falling mass of 0.84kg (29.5oz), released from a height of 67mm (2.625 inches) or other heights as required. Evaluation Cracking, chipping and breakage, any of which constitutes damage. Test the remaining specimens.
Product Information:
With the equipment the impact resistance of plastic sew-through flange buttons can be determined that a falling mass of 0.84kg (29.5oz) is released from a height of 67mm (2.625inch) or other heights as required. Cracking, chipping or breakage constitute failure.
Features:
1. Ensure the vertical alignment of tension;
2. Fixed button edge without affecting its adhesion;
3. Consistent force of 10s continuously;
4. Elevate and fix the position of the test meter through the handle, easy to change samples
5. Horizontal hand wheel, designed to cooperate with ergonomic principles to make operators more comfortable;
6. Safety buckle design makes operation more secure and reliable;
7. The long machine frame can extend the test scope more widely;
8. The concealed spring is designed to greatly increase the pin tightening and ensure the test repeatability;
9. Can reduce the damage caused by slid leakage during test process;
10. Simple design and accurate test results.
Technical Parameter
| Parameter | Specification |
|---|---|
| Operating Mode | Manual |
| Impact Head Weight | 0.84kg |
| Impact Height | 32mm, 44mm, 67mm, 83mm, 95mm, 117mm |
| Body Material | Stainless Steel / Brushed Finish |
| Instrument Weight | 5kg |
| Power Supply | No (Manual Operation) |
| Appearance Size | 100mm (L) × 150mm (W) × 300mm (H) |
Send product request
Other supplier products
 |
Absorbable Bone - connecting Plates Four - point Bending Tester | Standard ASTM F2119: Standard test method for constant load testing of bioabsorbable screws and washers, applicable to bending performance evalu... |
 |
Gakushin Tester丨Gakushin chamber | Content ThisGakushin Type Rubbing Testeris a standard testing machine of the Type II rubbing tester (GAKUSIN TYPE) specified in JIS L0849Test Meth... |
 |
Melt Mass-Flow Rate Test Machine, ASTM D1238-98 | Introduction: This machine is deisgned according to ISO1133. ASTM D1238-98 ,ISO1133; Melt flow rate was measured using automatic sampling, weigh... |
 |
SRV High-Frequency Reciprocating Friction and Wear Tester | SRV High-Frequency Reciprocating Friction and Wear Tester is a fully automated, computer-controlled tribological testing system designed to evaluat... |
 |
High-Speed Reciprocating Friction and Wear Tester (Model 2M) | The High-Speed Reciprocating Friction and Wear Tester (Model 2M) is designed for evaluating the friction and wear performance of materials and comp... |
Same products
 |
Plastic Smoke Density Tester F313 | Seller: Standard International Group (HK) Limited | The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ... |
 |
Xenon Test Chamber | Seller: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | Seller: Qinsun Instruments Co., LTD | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | Seller: Qinsun Instruments Co., LTD | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | Seller: Qinsun Instruments Co., LTD | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
