Carpet Peel Strength and Tuft Bond Tester
Product Details
For tufted carpets or traditional carpets, an important parameter is the retention performance of their tufts.
Poor - quality carpets may completely lose their tufts in certain situations, such as on staircases. For loop - pile carpets, well - formed loops can prevent the formation of long loops. This instrument can measure the force required to pull out a single tuft or loop from the carpet, that is, the bonding force between the carpet pile and the backing. This instrument is commonly used for testing small quantities of samples in laboratories, but it can also be applied in specific scenarios involving existing carpets or large - scale carpets.
Compliance Standards
BS 5229: 1975 (1996), ISO 4919: 1978
Test Method
The carpet sample is fixed by a steel template. Hold one end of the tuft to be tested with a pair of surgical forceps, or hook a loop with a metal hook. The surgical forceps or the metal hook is connected to a force - measuring balance, which is driven by a small electric motor to increase the pulling force at a steady rate. When the tension reaches its limit, the balance shows the required maximum tension. The maximum tension of the balance of the standard instrument is 5kg. When measuring carpets with greater tension, a balance with a capacity of 10kg can be selected. Dimensions: W430 mm, D300mm, H535 mm Power consumption: 20 W
Parameters
50 lbF, 25 kgF, 250 N
Peak memory for tensile loads
Accuracy: ± 0.3% of full scale ± digit
Safe overload: 150% accuracy
Selectable units of measurement: kg, N, or lbs
Push-button calibration
IPM – Intelligent Power Management system
Battery or AC operation
Send product request
Other supplier products
 |
High-precision Material Thermal Conductivity Tester | Introduction It adopts the internationally popular method of heat flow meter to detect thermal conductivity and thermal resistance, and realizes f... |
 |
Sharp edge meter | Standards : ASTM F963 4.8. EN71-1998 8.14. GB6675-2003 A.5.9. 16CFR 1500.48 Basic Configuration： Sharp Edge Tester: 1 unit Foot switch: 1 set ... |
 |
Enamel Boiling Water Mass Loss Tester | Product Introduction: The enamel layer boiling water weight loss tester is designed according to QB/T 2590-2003 Appendix A, GBT99892-2015 /ISO 287... |
 |
Wear Resistance Tester for Total Hip Joint Prostheses | Standard YY/T 0651.1-2016 (China): Specifies wear testing parameters for total hip prostheses, including angular motion, loading modes, and enviro... |
 |
EN sole zigzag testing machine | Product Introduction: The EN sole bending tester is used for 90 degree bending test of the sole of rubber, EVA and other zigzag shoes to detect it... |
Same products
 |
FH-77 Dissolved hydrogen meter | Seller: Kelilong Electron Co.,Ltd | Pen type dissolved hydrogen detector / dissolved hydrogen meter: used to measure the dissolved hy... |
 |
Xenon Arc Weather Ometer | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App: +86 181 0160 0864 SI4000Xenon Arc Weather Ometer utilizes a xenon lamp ... |
 |
Xenotest | Light Fastness Tester Si220 (SunTest) | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App:+86 180 0160 0864 A Light Fastness Tester, or Xenon Tester, Accelerated ... |
 |
Ozone Aging Chamber | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App:+86 156 1874 6768 The Ozone Aging Chamber is a precision testing instrum... |
 |
Plastic Smoke Density Tester F313 | Seller: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com The F313 Plastic Smoke Density Tester is ... |
