Rubber Mooney Viscosity Measuring Instrument (for Rubber Mooney Viscosity Tester)

• 

Test principle:

The Mooney viscometer is used to measure the viscosity of rubber under specific conditions. In the test, the rubber sample was loaded into the mold cavity of the Mooney viscometer and the motor was started after preheating, and the rotor began to rotate and a certain shear torque was applied. At the same time, the rubber sample produces an equal and opposite resistance moment, which is displayed by the dial indicator installed at one end of the worm or directly through the computer, that is, the Mooney viscosity value.

Reference standard:

GB/T 1232 unvulcanized rubber - Determination of Mooney viscosity

GB/T 1233 rubber compound -- Determination of initial vulcanization characteristics -- Mooney viscometer method

HG-T 3242-2017 Rubber Mooney viscometer

ISO289 unvulcanized rubber -- determination by shear disc viscometer

ISO667 rubber compound - Determination of initial vulcanization characteristics - Mooney viscometer method

Technical parameters:

Measurement and control temperature range: normal temperature ——200℃

Torque measuring range: 0-100 Mooney value

Calibration accuracy: 100±0.5 Mooney value

Rotor speed: 2±0.02 RPM

Measurement time: 0-200 points

Ambient temperature: 0-35℃

Relative humidity: <80%

Test pressure: 11.5KN±0.5KN

Air pressure: 0.45-0.6MPa

Test requirements:

1) Scope: This specification specifies the test method of Mooney viscosity of rubber compound.

Note: Measuring range includes: Mooney viscosity.

2) Test tools: Mooney viscometer, electronic scale, scissors, heat insulation gloves

3) Sample requirements: Cut two rubber samples with a diameter of about 45mm and a thickness of about 3mm from the bubble-free rubber material, one of which has a circular hole with a diameter of about 8mm in the center of the sample (two pieces of rubber material weigh about 16g)。

4) Test conditions: the rubber material can be tested for more than 2 hours under laboratory conditions after processing, but not more than 10 days.

Other supplier products

	Spray Aerosol Ignition Distance Tester	Product Description Conforms to UN Recommendations on the Transportation of Dangerous Goods - Manual of Tests and Criteria 31.4 Ignition Distance ...
	Falling ball impact testing machine	Product Introduction: Falling ball impact tester is suitable for testing the fastness of plastic, ceramic, acrylic, glass fiber and other material...
	Water Leak Detector	GB/T 21619-2008 Test Methods for Dangerous Goods Flammable Solids Emitting Flammable Gases in Contact with Water, GB 19521.4-2004 Safety Standard f...
	Solid Combustion Rate Tester	This product complies with "Recommendations on the Transport of Dangerous Goods - Manual of Tests and Criteria" 33.2.1.4 Test N.1: Test Method for ...
	Dust Cloud Tester	Dust Cloud Minimum Ignition Energy Tester disperses a certain mass of dust specimen to be tested into the Hartmann tube device through a certain pr...

Same products

	Xenon Test Chamber	Seller: Standard International Group (HK) Limited	Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli...
	Single Cable Vertical Flame Tester	Seller: Qinsun Instruments Co., LTD	Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ...
	Safety Helmet Flammability Tester	Seller: Qinsun Instruments Co., LTD	Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda...
	Furniture flammability tester	Seller: Qinsun Instruments Co., LTD	Product details Furniture flammability tester is mainly used to test the combustion performance ...
	Flame retardant testing machine	Seller: Qinsun Instruments Co., LTD	Feature highlights: Flame Retardant Tester is designed for testing plastic runway surface layers...