Button Impact Resistance Testing Machine (for Button Impact Machine)
Standards:
ASTM D5171: Test Method for Abrasion Resistance of Inks and Coatings (referenced for impact-related durability assessments).
Application:
Button falling weight impact testeris used to determine the impact resistance of plastic sew-through flange buttons to a falling mass of 0.84kg (29.5oz), released from a height of 67mm (2.625 inches) or other heights as required. Evaluation Cracking, chipping and breakage, any of which constitutes damage. Test the remaining specimens.
Product Information:
With the equipment the impact resistance of plastic sew-through flange buttons can be determined that a falling mass of 0.84kg (29.5oz) is released from a height of 67mm (2.625inch) or other heights as required. Cracking, chipping or breakage constitute failure.
Features:
1. Ensure the vertical alignment of tension;
2. Fixed button edge without affecting its adhesion;
3. Consistent force of 10s continuously;
4. Elevate and fix the position of the test meter through the handle, easy to change samples
5. Horizontal hand wheel, designed to cooperate with ergonomic principles to make operators more comfortable;
6. Safety buckle design makes operation more secure and reliable;
7. The long machine frame can extend the test scope more widely;
8. The concealed spring is designed to greatly increase the pin tightening and ensure the test repeatability;
9. Can reduce the damage caused by slid leakage during test process;
10. Simple design and accurate test results.
Technical Parameter
| Parameter | Specification |
|---|---|
| Operating Mode | Manual |
| Impact Head Weight | 0.84kg |
| Impact Height | 32mm, 44mm, 67mm, 83mm, 95mm, 117mm |
| Body Material | Stainless Steel / Brushed Finish |
| Instrument Weight | 5kg |
| Power Supply | No (Manual Operation) |
| Appearance Size | 100mm (L) × 150mm (W) × 300mm (H) |
Send product request
Other supplier products
 |
Bone Plates Four-point Bending Fatigue Tester | Standard YY/T 1503-2016: Chinese standard specifying test methods for bending fatigue properties of metallic bone plates, requiring 1 million ... |
 |
Fabric Friction Charge Tester | Friction charged charge tester Friction Charging Tester is the antistatic fabric and knitted fabric friction generated by the amount of charged cha... |
 |
Automotive Wires Flammability Tester | Compliance Standards FMVSS 302 (Federal Motor Vehicle Safety Standard) ISO 6722 (Road Vehicle Cable Flammability) UL 94 (Tests for Flammability ... |
 |
Metal Wire Repeated Bending Tester | Meet the standard GB/T 238-2013 "Metal material wire repeated bending test method" GB/T 235 "Metal material thickness is less than or equal to 3m... |
 |
Anti-glare Panel Falling Weight Tester | Scope of application: The anti-glare board impact testing machine is designed and produced for each testing unit to measure the impact resistance ... |
Same products
 |
Plastic Smoke Density Tester F313 | Seller: Standard International Group (HK) Limited | The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ... |
 |
Xenon Test Chamber | Seller: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | Seller: Qinsun Instruments Co., LTD | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | Seller: Qinsun Instruments Co., LTD | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | Seller: Qinsun Instruments Co., LTD | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
