SL52/SL62/SL72/SL82/SL92/SL102/SL81 Square reinforcing mesh
Reinforcing mesh was made by deformed bar after drawn, which is accorded to Australian/New Zealand Standard AS-NZS 4671-2001. The material is 250N, 300E, 500L, 500N and 500E, the mesh spaces is 200mm, there is two sides overhang which is 100mm.
the steel bar after drawing shape as below figure:
- The angle of the rib or inclined indentation of the reinforcing mesh panels' bar isn't less than 45°. The angle scope is greater than 45° and is less than 70°, the rib height is from 0.025d to 0.10d.
- includes transverse and longitudinal bar, pitch and overhang. The Australian and new zealand's market, the normal panel size is 2.4m*6m.Because of containers size, we always advise our cutomer to make the panel size to be 2.2m*5.8m. It can be easy to be load and save more USD1000 per container for packing and loading cost.
- Each sheet of reinforcing mesh panel shall include number of bars,pitch,length,width, and overhang dimensions. And the bar arrangement of panel has single bars, twin bars or combination of single bars and twin bars.
- is contained composition and characteristic mechanical porperties of reinforcing steels.
Table1
Composition of reinforcing steels
|
Type of analysis |
Chemical composition, % max |
|||||||
|
All grades |
Carbon equivalent value(Ceq)for standard grades |
|||||||
|
C |
P |
S |
250N |
500L |
500N |
300E |
500E |
|
|
Cast analysis |
||||||||
|
Products analysis |
||||||||
Table 2
Characteristic mechanical properties of reinforcing steels
|
Property |
250N(Note1) |
500L(Note1) |
500N |
300E(Seismic) |
500E(Seismic) |
Type of specified value |
|
Yield Stress(Mpa) RekLRekU |
≥ |
≥500≤750 |
≥500≤650 |
≥300≤380 |
≥500≤600 |
CvL: p=0.95CvU: p=0.05 |
|
Ratio Rm/Re |
≥1. |
≥1. |
≥1.08-------- |
≥1.15≤1.50 |
≥1.15≤1.40 |
CvL: p=0.90CvU: p=0.10 |
|
Unitform Elogation Agt(%) |
≥5.0 |
≥1.5 |
≥5.0 |
≥15.0 |
≥10.0 |
CvL: p=0.90 |
Common size of for Austialian Market
|
Mesh Type and reference number |
Longitudinal bars |
Cross-bars |
Mass for 6 x2.4 m sheets |
Cross-sectional area/m width |
||||
|
Pitch@mm |
Pitch@mm |
Unit area kg/sqm |
Sheet, kg |
Long'l bars sqmm/m |
Cross bars sqmm/m |
|||
|
Squre, with edge side-lapping bars |
||||||||
|
SL102 |
10 x 9.5 + 4 x 6.75 |
200100 |
30 x 9.5 |
200 |
80 |
354 |
354 |
|
|
SL92 |
10 X 8.6 + 4 X 6.0 |
200100 |
30 x 8.6 |
200 |
66 |
290 |
290 |
|
|
SL82 |
10 x 7.6 + 4 x 6.0 |
200100 |
30 x 7.6 |
200 |
52 |
227 |
227 |
|
|
SL72 |
10 x 6.75 + 4 x 5.0 |
200100 |
30 x 6.75 |
200 |
41 |
179 |
179 |
|
|
SL62 |
10 x 6.0 + 4 x 5.0 |
200100 |
30 x 6.0 |
200 |
33 |
141 |
141 |
|
|
Squre, without edge side - lapping bars |
||||||||
|
SL81 |
25 X 7.6 |
100 |
60 x 7.6 |
100 |
105 |
454 |
454 |
|
We are .
How can we conctrol our products quality for exporting Autralia?
Firstly, we purchase the material from Steel Factory and inspect chemical composition and mechnical property of reinforcing mesh panel in our in-house laboratary according to AS 1554.3.
Secondly, the panel size tolerances meassure way as:
Notes:
Send product request
Other supplier products
 |
Steel Wire Mesh | The steel wire mesh is always used on multi-story buildings, bridges, road reinforcement, vetical highway supports, etc. According to the wire di... |
|
|
SL52/SL62/SL72/SL82/SL92/SL102/SL81 Square reinforcing mesh | Reinforcing mesh was made by deformed bar after drawn, which is accorded to Australian/New Zealand Standard AS-NZS 4671-2001. The material is 250... |
 |
PPAF R / PPAF C / PPAF V BRC Mesh / reinforcement meshes | Heyou wire mesh factory can supply reinforcement meshes accordance to Normes Francaises NF A 35 016-1996. The material of reinforcement meshes o... |
 |
SL51.5/ SL41.5 construction reinforcement mesh by AS-NZS 4671-2001 standard | was made by plain steel wire. It main used on building construction complied with standard AS NZS 4671-2001. The material is 250N, 500N, 500L, 3... |
 |
Strip Foundation mesh reinforcement A393 | umber of strip foundation mesh stock which is fit for meeting the requirements for most British domestic house. was made by heyou wire mesh factor... |
Same products
 |
Micro Perforated Metal | Seller: Hebei Baima Wire Mesh Manufacturing Co., Ltd | Micro Perforated Metal Micro Perforated Metal Sheet , widely Used in Filter Production, wit... |
 |
Micro Perforated Stainless Steel Sheet | Seller: Hebei Baima Wire Mesh Manufacturing Co., Ltd | Micro Perforated Stainless Steel Sheet Micro Perforated Stainless Steel Sheet Supplier | Pre... |
 |
Micro Perforated Aluminum Sheet | Seller: Hebei Baima Wire Mesh Manufacturing Co., Ltd | Micro Perforated Aluminum Sheet | Custom Precision-Perforated Aluminum Panels High-Precis... |
 |
Custom Perforated Metal | Seller: Hebei Baima Wire Mesh Manufacturing Co., Ltd | Custom Perforated Metal Perforated Sheet is a product of using mechanical stamping to for... |
 |
Perforated Plate Composite Sintered Mesh | Seller: Hebei Da Shang Wire Mesh Products Co.,Ltd. | Perforated Plate Composite Sintered Mesh Perforated plate composite sintered meshhas become a ve... |
