AISI O1 Tool Steel | 1.2510 | 100MnCrW4 | SKS3
AISI O1 Steel is ahighquality Cold work tool steel, Itbelong to the high quality high carbon alloy tool steel. Oil Quenched & Tempered Hardenss is 28-34 HRc. AISI o1 steel Annealing delivery hardenss less than 250HB.
Related SpecificationsASTM A29/A29M DIN EN 10083/3 JIS G4053 GB GB/T 3077
01 tool Steel PDF DOWN
Form of Supply
AISI o1 tool steel, we can supply the round bar, steel flat bar, plate, hexagonal steel bar and steel square block. AISI o1 steel Round barcan be sawn to your required lengths as one offs or multiple cut pieces. O1 steel Rectangular pieces can be sawn from flat bar or plate to your specific sizes. Ground tool steel bar can be supplied, providing a quality precision finished bar to tight tolerances.
-
Round
-
Plate
-
sheet
-
Square
Chemical composition
| C(％) | 0.85～1.00 | Si(％) | 0.10～0.50 | Mn(％) | 1.00～1.40 | P(％) | ≤0.030 |
| S(％) | ≤0.040 | Cr(％) | 0.40～0.60 | V (％) | ≤0.30 | W(％) | 0.40～0.60 |
Heat treatment Related
-
Annealingof O1 Tool steel
Slowly heated to 740-760 ℃（1364-1400℃） and allow enough times, let the steel to be thoroughly heated, Then cool slowly in the furnace. The o1 tool steel will get MAX 250 HB （Brinell hardness）.
-
Hardening of o1 tool steel
O1 steels should be heated uniformly to 780-820°C (1436-1508°F) until completely heated through. If needed, the steels can be preheated at 300-500°C (572-932°F). About 30 min/per 25 mm of ruling section is to be provided and then the steels should be immediately quenched in oil.
-
Tempering of o1 tool steel
Tempering of O1 steels is performed at 100-350°C (212-662°F), Soak well at the selected temperature and soak for at least one hour per 25mm of total thickness. Get Rockwell C hardness of 55 to 64.
Temperature [℃] 100 150 200 250 300 350
Hardness [HRc] 64-63 63-62 62-61 60-59 58-57 56-55
Mechanical Properties
The mechanical properties of O1 tool steels are outlined in the following table.
| Elastic modulus (@399°C/750°F, hardened to 62 HRC ) |
Elastic modulus (hardened to 62 HRC) | Yield (0.2%, hardened to 55 HRC) |
Yield (0.2%, hardened to 60 HRC) |
Yield (0.2%, hardened to 62 HRC) |
Yield (0.2%,hardened to 50 HRC) |
|
| GPa | GPa | Mpa | Mpa | Mpa | MPa | |
| 172 | 193 | 1800 | 2150 | 2200 | 1350 | |
Applications
O1 steels are mainly used for short run tooling for cold forming dies, blanking dies, and cutting tools operating at ambient temper.
O1 tool steel typical applications include medium run dies, intricate press tools, drawing punches, broaches, bushings, lathe centres, chuck jaws, master cavity sinking hobs, paper cutting machine knives, plug gauges, thread gauges and precision measuring tools. Also commonly used in applications such as cams, cloth cutting knives, cold taps, reamers, collets, cutting hobs, strip slitting cutters, trimmer dies, tube expander rolls, plastic moulds and woodworking knives ature.
Regular size and Tolerance
| 1) Hot Rolled round bar | |||
| Diameter (mm) |
Diameter Tolerance (mm) |
Diameter (mm) |
Diameter Tolerance (mm) |
| ≤12.70 | -0.13 ～0.30 | >50.80～63.5 | -0.25～0.76 |
| 12.7～25.40 | -0.13～0.41 | >63.50～76.20 | -0.25～1.02 |
| >25.4～38.10 | -0.15～0.51 | >76.20～101.60 | -0.30～+1.27 |
| >38.1～50.80 | -0.20～0.64 | >101.60～203.20 | -0.38～3.81 |
| 2) Hot Rolled steel plate | |||
| Thickness (mm) |
Thickness Tolerance (mm) |
Thickness (mm) |
Thickness Tolerance (mm) |
| ≤25.4 | -0.41～0.79 | >127～152 | -1.60～2.39 |
| >25.4～76 | -0.79～1.19 | >178～254 | -1.98～3.18 |
| >76～127 | -1.19～1.60 | >254～305 | -2.39～3.96 |
Others O1 have not specified size, plscontactourexperienced sales team.
AISI o1 tool steel round bar and flat sections can be cut to your required sizes. O1 tool steel ground bar can also be supplied, providing a high quality tool steel precision ground tool steel bar to your required tolerances. AISI o1 steel is also available as Ground Flat Stock / Gauge Plate, in standard and nonstandard sizes.
Send product request
Other supplier products
 |
AISI 1045 STEEL, 45# carbon steel | AISI 1045 steel is a medium carbon, medium tensile steel supplied as forged or normalized. This steel shows reasonable strength and toughness. AISI... |
|
|
D2 Tool Steel | 1.2379 | X153CrMo12 | SKD11 | Cold Works D2 tool steel is a high carbon, high chromium tool steel (12% chrome) with extremely high wear-resisting properties, heat treatable to 6... |
 |
AISI 4140 Alloy Steel | 1.7225 | SCM440 | 42CrMo4 | AISI4140Alloy steel material stockholders and suppliers from China-OTAI SPECIAL STEEL . we have more 16 years experience in 4140 steel plate, round... |
|
|
M2 Tool Steel | 1.3343 | HS-6-5-2C| SKH51 | AISIM2 Tool Steelis molybdenum based high-speed steel in tungsten–molybdenum series.HSSgrade steelM2is a medium alloyed high speed steel whic... |
|
|
AISI 8620 Steel | 1.6523 | 21NiCrMo2 | SNCM220 alloy steel | AISI8620 Steelis a low alloy nickel, chromium, molybdenum case hardening steel, as a common, carburizing alloy steel, it is more responsive to mech... |
Same products
 |
CK800 Flat Bed Lathe | Seller: Taizhou Eastern CNC Technology Co., Ltd. | The CK800 Flat Bed Lathe carriage in the machine tool adopts a double tool holder design, which i... |
 |
stainless steel filter elements | Seller: ZHUAN LV FILTRATION | stainless steel filter elements Stainless Steel Filter Cartridges/Elements Stainless Stee... |
 |
Stainless Steel Banding Strap Strip for Pole Clamp | Seller: Nanjing Suntay Steel Co., Ltd | Stainless Steel strappingis ideal for cable and pipe banding applications that require various bu... |
 |
Aluminum Clad Steel Wire | Seller: Nanjing Suntay Steel Co., Ltd | Typical Application:Power line crossing water, Power line in industrial ,semi-industrial or coast... |
 |
Steel Wire Rope For Wind Power Generation | Seller: Nanjing Suntay Steel Co., Ltd | Steel wire rope for wind power generationis a high-performance produtc specially designed and man... |
