METAL FLANGING

• 

Flanging refers to the stamping process of turning the edge or outer edge of the hole on the workpiece into an upright straight edge with a die. It is included in the forming process of stamping.

WHAT IS THE ADVANTAGE OF METAL FLANGING?

It can process precision stamping parts with complex shape and good rigidity.

Improve the production efficiency. Save dies for some deep drawing parts. Reduce the manufacturing cost.

It can replace the deep drawing work of a complex shape workpiece, so flanging is especially suitable for small batch trial production.

Flanging is usually applied at the edge of the stamping part, which can effectively save the material.

WHAT SHOULD BE CONCERNED IN METAL FLAGGING?

Flanging is a stamping method that turns the workpiece with holes punched in advance into vertical flange along the hole edge. The deformation of hole flanging is from the tensile deformation of the material along the tangential direction, and the closer to the edges, the greater the deformation and the flanged area of workpiece gets thinner. Due to that, the hole edge may be cracked if not dealt properly. In order to prevent the cracking, the flanging degree of the inner hole of the workpiece must not be too large. If the flanging height is large, we can process flanging several times instead.

In flanging, the deformation degree is expressed by cofficient "K", which is the ratio of the aperture before flanging to the aperture after flanging. Obviously, the larger the value of K, the smaller the degree of deformation. On contrary, the smaller the value of K, the greater the degree of deformation, and more likely the edge of the flanging hole will be broken. The minimum value of K occurs with the maximum deformation degree which can be achieved without cracking the hole edge.

In order to prevent edge cracking, K shall not be too small and shall be greater than the minimum value introduced above. Experience shows that the minimum value of K is not only related to the type and performance of the material, but also to the relative thickness of the blank, and the shape of the product.

If you need any kinds of metal work fabrication, please contact us, as a professional metalworking factory, Hongkun is willing to offer you high quality products.

Другие товары поставщика

	AUTOMOTIVE PARTS	There are tremendous metal stamping parts you can find on a car. From a small clip to the entire body frame, the production of a car is always stro...
	METAL DEEP DRAWING	Metal deep drawing chinarefers to a kind of machining process in which a certain shape of flat blank obtained after blanking is stamped into variou...
	CAR SEAT BRACKET	The main function of custom car seat bracketsis to keep the driver in a correct sitting position, provide support for the upper body when turning, ...
	METAL HEMMING	Metal hemming is a process that involves folding the edge of the sheet metal to 180° onto itself. Then, two newly formed layers are flush with ...
	METAL PUNCHING	Metal punching serviceis a key part of Hunkmachining's services, mostly applied to automobile parts. As a metal punching factory, metal punching co...

Похожие товары

	Common Rail Fuel Injector Control Valve F00R J02 377	Продавец: 838623	Common Rail Fuel Injector Control Valve F00R J02 377 (BRE) Whats--App Alen----(at)----china-lu...
	Common Rail Fuel Injector Control Valve F00R J02 130	Продавец: 828487	Common Rail Fuel Injector Control Valve F00R J02 130 (BRE) Whats--App Alen----(at)----china-lu...
	diesel common rail nozzle G3S80 diesel common rail nozzle L087PBD	Продавец: 838623	diesel common rail nozzle G3S80 diesel common rail nozzle L087PBD (BRE) Whats--App Alen----(a...
	diesel common rail nozzle G3S84 diesel common rail nozzle L078PBD	Продавец: 828487	diesel common rail nozzle G3S84 diesel common rail nozzle L078PBD (BRE) Whats--App Alen----(a...
	2UUL Vajra Screen Separation Wire For Phone Repair 0.035mm	Продавец: Shenzhen Wikshu Technology Co.	Описание 2UUL DA21 Ваджра проволока экрана разделения линии 0.035MM*100M. 0.035 мм высокая твердо...