Wyzenbeek or Oscillatory Abrasion Tester，custom wyzenbeek/Oscillatory Abrasion Tester

Wyzenbeek wear resistance tester, also known as Oscillatory wear resistance tester, is used to test the wear resistance of fabrics against standard friction media or metal mesh surface friction movement, especially suitable for automotive decoration and furniture textile product. Instrument regulations American standard. There are 4 friction heads and electronic counter to control the running cycle.

Application

1. Automotive Industry

Testing the abrasion resistance of seat fabrics and steering wheel leather to evaluate durability during long-term use.

Simulating the friction between seats and passenger clothing to optimize material selection and reduce wear rate.

Testing the abrasion resistance of aircraft interior materials under extreme conditions such as high altitude and low temperature.

2. Furniture Industry

Testing the abrasion resistance of textiles used in sofas, chairs, and other furniture to ensure product lifespan meets standards.

Comparing the abrasion resistance of different fabric structures to guide product improvement.

3. Materials Research and Development

Providing abrasion resistance data support for new fiber materials and coating processes.

Comparing the impact of different treatment processes (such as waterproofing and fire resistance) on abrasion resistance.

4. Third-Party Testing

Serving as a third-party testing device to verify whether materials meet international standards (such as ASTM D4157. BS EN ISO 12402-7. FTMS 191A 5304. etc.).

5. Electronics Industry

Verifying the friction resistance lifespan of mobile screen protectors, touch panels, and keyboard coatings.

6. Packaging Industry

Testing the abrasion resistance of labels and packaging films to prevent information blurring, coating peeling, or damage due to friction during transportation or storage.

Standard Test

ASTM D3597：Standard Test Method for Resistance to Yarn Slippage in Woven Fabrics Using a Fixed Load

ASTM D4157：Standard Test Method for Abrasion Resistance of Textile Fabrics (Oscillatory Cylinder Method)

CFFA-1A：Standard Test Method for Seam Slippage of Upholstery Fabrics

FED-STD-191 / Method 5304：Textile Test Methods – Method 5304: Seam Slippage

GM2756M：Abrasion Resistance of Interior Trim Materials

LP-463KB-06-01：Abrasion Resistance Test for Interior Trim Materials

LP-463KC-04-01：Seam Slippage Resistance Test for Interior Trim Fabrics

SAE J948：Abrasion Resistance of Upholstery Materials

SAE J1530：Seam Slippage Resistance of Upholstery Fabrics

Toyota TSL 5101G – 3.9.4：Abrasion Resistance Test for Interior Trim Materials

Feature

Easy to control due to the precision electronic digital counter.

The protective cover provides protection and thus more safety.

Four abrasion heads to test samples simultaneously, thus greater efficiency.

Parameters

Technical Parameter	Specification
1. Design Style	Modern ergonomic design
2. Suction Device	Connected to the auxiliary vacuum cleaner
3. Transmission Feature	Sealed transmission (ensures quiet operation)
4. Test Position	4 heads
5. Friction Table	Curve surface-R100mm, length-400mm
6. Swing Radian	76±2mm
7. Friction Rate	90±1/min (double friction)
8. Tension Adjustment Weight	340g (tension adjustment range: 8.9N-22.25N)
9. Load Adjustment Weight	150g (load adjustment range: 8.9N-17.8N)
10. Sample Tension	17.8N (adjustable)
11. Sample Load	13.4N (adjustable)
12. Sponge Rubber Pressure Pad	50×50mm (±1mm)
13. Instrument Material	Stainless (steel)
14. Surface Finishing	Painting
15. Sample Dimension	245×73mm
16. Product Dimension (L×W×H)	50×50×60

Accessoriess

Standard accessories:Abrasion media (e.g., standard abrasive paper/cloth), sample fixing clamps, standard weights, digital counter, power cord, user manual, certificate of conformity, and calibration tools (for some models).

Optional accessories: Additional abrasion media, specialized abrasive heads, temperature/humidity control modules, pre-tension adjustment fixtures, and result evaluation auxiliary tools (e.g., light boxes).

Test Procedures

1. Sample Preparation

Cut test specimens according to the standard (commonly 120mm×20mm, 140mm×50mm, etc.), and condition them for 24 hours (23±2℃, 50±5% RH). Elastic leather samples should be stretched by 10% (or to the maximum stable elongation).

2. Equipment and Medium Pre-treatment

Clean the platform and calibrate the pressure (500g for dry friction / 1000g for wet friction); for wet friction, treat the wool felt/cotton cloth with boiling water and squeeze out excess water until it weighs approximately 1g (or has a water absorption rate of 100±5%).

3. Parameter Setting and Testing

Select dry/wet mode, set the number of friction cycles (5-500 cycles, e.g., ISO 11640 specifies 50 cycles for dry rubbing and 10 cycles for wet rubbing), and speed (30-60 cycles/minute); fix the sample and friction medium, and start the instrument until the preset number of cycles is reached.

4. Result Evaluation

Under D65 light source, use a gray scale to evaluate the staining grade of the friction medium (grades 1-5) and the discoloration grade of the leather. Record whether there is pilling/cracking on the surface. Take the lower value from parallel tests.

Другие товары поставщика

	Qinsun SUNTEST XXL+	Qinsun SUNTEST XXL+is a large xenon lamp weathering and photoaging tester that complies with various ISO, ASTM, and ICH industry standards. The exp...
	Automatic Cap Torque Tester	A Bottle Cap Torque Tester is a specialized device used to measure the torque applied to bottle caps during sealing or opening processes. Its prima...
	Molten Metal Penetration Resistance Tester	Standard ISO 9185(Protective Clothing - Assessment of Resistance to Molten Metal Splash) ASTM F955(Standard Test Method for Evaluating Heat Tra...
	Perspiration Tester 丨Perspiration Test machine	Compliant Standards ISO 105 E01: Textiles - Tests for colour fastness - Part E01: Colour fastness to water ISO 105 E02: Textiles - Tests for colo...
	Fire retardant wood wood stack method burning test equipment	Product Introduction: Fire retardant wood stack method combustion test device is a test device developed and produced by referring to the People's...

Все товары поставщика

Похожие товары

	Air Intake Filter Test System	Продавец: Standard Groups	The Air Intake Filter Test System is designed for testing industrial air filters and engine air f...
	Mattress Spring Fatigue Tester，ASTM D3574 ，how to test mattress for sagging	Продавец: Standard International Group (HK) Limited	The King Size Foam Fatigue Tester is a single-station pneumatic fatigue testing system designed f...
	Mattress Rollator，ASTM F1566 ，Mattress Durability Tester，Mattress Fatigue Tester	Продавец: Standard International Group (HK) Limited	The Mattress Rollator is a laboratory durability testing system designed to evaluate the long-ter...
	HD2 Pneumatic Foam Fatigue Tester，ISO 3385，Foam Fatigue Testing Machine	Продавец: Standard International Group (HK) Limited	The HD2 Pneumatic Foam Fatigue Tester is a heavy-duty, single-station laboratory testing machine ...
	VW Heel Abrasion Tester，ISO 4649 ，Heel Performance Testing Machine	Продавец: Standard International Group (HK) Limited	The VW Heel Abrasion Tester is designed to evaluate the wear resistance of floor covering materia...