Wyzenbeek or Oscillatory Abrasion Tester，custom wyzenbeek/Oscillatory Abrasion Tester
Wyzenbeek wear resistance tester, also known as Oscillatory wear resistance tester, is used to test the wear resistance of fabrics against standard friction media or metal mesh surface friction movement, especially suitable for automotive decoration and furniture textile product. Instrument regulations American standard. There are 4 friction heads and electronic counter to control the running cycle.
Application
1. Automotive Industry
Testing the abrasion resistance of seat fabrics and steering wheel leather to evaluate durability during long-term use.
Simulating the friction between seats and passenger clothing to optimize material selection and reduce wear rate.
Testing the abrasion resistance of aircraft interior materials under extreme conditions such as high altitude and low temperature.
2. Furniture Industry
Testing the abrasion resistance of textiles used in sofas, chairs, and other furniture to ensure product lifespan meets standards.
Comparing the abrasion resistance of different fabric structures to guide product improvement.
3. Materials Research and Development
Providing abrasion resistance data support for new fiber materials and coating processes.
Comparing the impact of different treatment processes (such as waterproofing and fire resistance) on abrasion resistance.
4. Third-Party Testing
Serving as a third-party testing device to verify whether materials meet international standards (such as ASTM D4157. BS EN ISO 12402-7. FTMS 191A 5304. etc.).
5. Electronics Industry
Verifying the friction resistance lifespan of mobile screen protectors, touch panels, and keyboard coatings.
6. Packaging Industry
Testing the abrasion resistance of labels and packaging films to prevent information blurring, coating peeling, or damage due to friction during transportation or storage.
Standard Test
ASTM D3597：Standard Test Method for Resistance to Yarn Slippage in Woven Fabrics Using a Fixed Load
ASTM D4157：Standard Test Method for Abrasion Resistance of Textile Fabrics (Oscillatory Cylinder Method)
CFFA-1A：Standard Test Method for Seam Slippage of Upholstery Fabrics
FED-STD-191 / Method 5304：Textile Test Methods – Method 5304: Seam Slippage
GM2756M：Abrasion Resistance of Interior Trim Materials
LP-463KB-06-01：Abrasion Resistance Test for Interior Trim Materials
LP-463KC-04-01：Seam Slippage Resistance Test for Interior Trim Fabrics
SAE J948：Abrasion Resistance of Upholstery Materials
SAE J1530：Seam Slippage Resistance of Upholstery Fabrics
Toyota TSL 5101G – 3.9.4：Abrasion Resistance Test for Interior Trim Materials
Feature
Easy to control due to the precision electronic digital counter.
The protective cover provides protection and thus more safety.
Four abrasion heads to test samples simultaneously, thus greater efficiency.
Parameters
| Technical Parameter | Specification |
|---|---|
| 1. Design Style | Modern ergonomic design |
| 2. Suction Device | Connected to the auxiliary vacuum cleaner |
| 3. Transmission Feature | Sealed transmission (ensures quiet operation) |
| 4. Test Position | 4 heads |
| 5. Friction Table | Curve surface-R100mm, length-400mm |
| 6. Swing Radian | 76±2mm |
| 7. Friction Rate | 90±1/min (double friction) |
| 8. Tension Adjustment Weight | 340g (tension adjustment range: 8.9N-22.25N) |
| 9. Load Adjustment Weight | 150g (load adjustment range: 8.9N-17.8N) |
| 10. Sample Tension | 17.8N (adjustable) |
| 11. Sample Load | 13.4N (adjustable) |
| 12. Sponge Rubber Pressure Pad | 50×50mm (±1mm) |
| 13. Instrument Material | Stainless (steel) |
| 14. Surface Finishing | Painting |
| 15. Sample Dimension | 245×73mm |
| 16. Product Dimension (L×W×H) | 50×50×60 |
Accessoriess
Standard accessories:Abrasion media (e.g., standard abrasive paper/cloth), sample fixing clamps, standard weights, digital counter, power cord, user manual, certificate of conformity, and calibration tools (for some models).
Optional accessories: Additional abrasion media, specialized abrasive heads, temperature/humidity control modules, pre-tension adjustment fixtures, and result evaluation auxiliary tools (e.g., light boxes).
Test Procedures
1. Sample Preparation
Cut test specimens according to the standard (commonly 120mm×20mm, 140mm×50mm, etc.), and condition them for 24 hours (23±2℃, 50±5% RH). Elastic leather samples should be stretched by 10% (or to the maximum stable elongation).
2. Equipment and Medium Pre-treatment
Clean the platform and calibrate the pressure (500g for dry friction / 1000g for wet friction); for wet friction, treat the wool felt/cotton cloth with boiling water and squeeze out excess water until it weighs approximately 1g (or has a water absorption rate of 100±5%).
3. Parameter Setting and Testing
Select dry/wet mode, set the number of friction cycles (5-500 cycles, e.g., ISO 11640 specifies 50 cycles for dry rubbing and 10 cycles for wet rubbing), and speed (30-60 cycles/minute); fix the sample and friction medium, and start the instrument until the preset number of cycles is reached.
4. Result Evaluation
Under D65 light source, use a gray scale to evaluate the staining grade of the friction medium (grades 1-5) and the discoloration grade of the leather. Record whether there is pilling/cracking on the surface. Take the lower value from parallel tests.
Send product request
Other supplier products
 |
Leather thickness tester | Product Introduction Leather thickness tester is a special high-precision instrument for leather thickness measurement, which can be widely used f... |
 |
Prefilled Syringe Plunger Force Tester | The Prefilled Syringe Plunger Force Tester is widely used in the medical device industry, mainly for testing the push - force performance of prefil... |
 |
Safety Helmet Impact Acceleration Tester | The safety helmet impact acceleration tester is an instrument used to test the performance of safety helmets when subjected to impact. It can simul... |
 |
Spring torsion fatigue testing machine | The Spring Torsion Fatigue Testing Machine (horizontal type) is an advanced automatic torsional fatigue testing instrument with digital display and... |
 |
zipper reciprocating fatigue testing machine | Application The instrument is widely used to evaluate the durability and service life of zippers with various length in the fields of clothing acc... |
Same products
 |
Air Intake Filter Test System | Seller: Standard Groups | The Air Intake Filter Test System is designed for testing industrial air filters and engine air f... |
 |
Mattress Spring Fatigue Tester，ASTM D3574 ，how to test mattress for sagging | Seller: Standard International Group (HK) Limited | The King Size Foam Fatigue Tester is a single-station pneumatic fatigue testing system designed f... |
 |
Mattress Rollator，ASTM F1566 ，Mattress Durability Tester，Mattress Fatigue Tester | Seller: Standard International Group (HK) Limited | The Mattress Rollator is a laboratory durability testing system designed to evaluate the long-ter... |
 |
HD2 Pneumatic Foam Fatigue Tester，ISO 3385，Foam Fatigue Testing Machine | Seller: Standard International Group (HK) Limited | The HD2 Pneumatic Foam Fatigue Tester is a heavy-duty, single-station laboratory testing machine ... |
 |
VW Heel Abrasion Tester，ISO 4649 ，Heel Performance Testing Machine | Seller: Standard International Group (HK) Limited | The VW Heel Abrasion Tester is designed to evaluate the wear resistance of floor covering materia... |
