Coating Surface Performance Tester

Whats/App: +86 156 1874 6768

Web: standard-groups.com

Application

Electronic product surfaces: Evaluation of wear resistance and color fading of coatings on mobile housings and keypads

Paper and printing materials: Measurement of friction between paper surfaces to prevent paper jams in printers and copiers

Abrasive materials: Quantification of grinding performance and wear characteristics of sandpaper

Rubber materials: Wear resistance testing of rubber components, including observation of automotive tire wear behavior

Rubber–glass interfaces: Friction performance evaluation between rubber and glass, such as wiper blade interaction with windshields

Flat materials: Friction performance testing of various flat sheet and panel materials

Environmental testing: Friction and wear testing under oil immersion, elevated temperature, or cooling conditions

Coated surfaces: Friction, wear, and scratch testing of coatings across different material systems

Typical test samples include:

Plastic housings and coated components

Paper and paperboard materials

Rubber products and elastomers

Glass and coated glass surfaces

Films, sheets, and surface-treated panels

Standards

GB/T 6040-2008 Test Method for Wear Resistance of Metal Surfaces

GB/T 9279-2007 Paints and Varnishes — Cross-Cut Test

JIS K 7125 Plastics — Tribological Test Methods

JIS K 5600 Testing Methods for Paints and Varnishes (including scratch, abrasion, and adhesion tests)

JIS L 0823 Test Methods for Abrasion Resistance of Plastic Films and Sheets

JIS P 8139 Determination of Friction and Wear Properties of Coatings

JIS P 8147 Determination of Surface Friction Coefficient and Scratch Properties of Coatings

ASTM D1894 Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting

Parameters

Parameter Category	Specification
Sliding speed	5 – 6000 mm/min
Drive motor	AC servo motor
Drive mechanism	Gear and rack transmission
Sliding distance	1 – 100 mm
Motion mode	Single mode: stops automatically after preset distance
	Reciprocating mode: preset distance, up to 99.999.999 cycles
Measurement range	10 – 100 gf or 0 – 2000 gf
Worktable size	240 × 120 mm
Safety system	Overload protection (OVERLOAD)
Noise suppression	High-frequency noise suppression circuit
Zero adjustment	Digital servo automatic zeroing
Output (non-linearity)	0 – 5 V (within 0.05% FS)
Sensitivity switching	0 / 10 / 25 / 50 / 100% FS
Dynamic strain amplifier	S/N ratio: 60 dB (maximum sensitivity)
Frequency response	2 kHz / −3 dB
Filter	1 / 10 / 100 Hz low-pass filter
Operating environment	0 – 50 °C, ≤85% RH, non-condensing
Power supply	AC 100 V, 50/60 Hz
Main unit dimensions	W 630 × D 350 × H 580 mm

Features

Linear motion driven by a servo motor ensures stable and precise friction testing

Balanced mechanical arm structure minimizes the influence of adapter weight on vertical load

Direct transmission of friction force to the load sensor improves measurement accuracy

Supports a wide range of test heads and accessories for versatile surface performance evaluation

Touchscreen interface enables intuitive operation and real-time data display

Capable of testing under special environments, including lubricated, heated, or cooled conditions

Test Procedures

Fix the test specimen securely on the worktable.

Select and install the appropriate test head according to the test method.

Set test parameters such as speed, sliding distance, load, and motion mode.

Adjust environmental conditions if required (oil, heating, or cooling).

Start the test and monitor friction force and surface behavior in real time.

Complete the test automatically or manually after the preset conditions are met.

Analyze test results based on the applicable standard and test objective.

Maintenance Information

Clean the worktable and test heads after each test

Inspect mechanical arms and transmission components regularly

Verify load sensor performance and zero calibration periodically

Keep electronic components free from dust and moisture

Store accessories and weights properly to prevent damage

Другие товары поставщика

	Knee Joint Prostheses Wear Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard ISO 14243-1:2014: Specifies wear testing parameters for total knee prostheses, in...
	Flame Spread Index Tester，ASTM E648 Flame propagation of carpet materials	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Flame Spread Index Tester is designed to evaluate the flame propagation characteristics...
	Tabletop xenon arc weathering tester for laboratory	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com The Water-Cooled Xenon Lamp Weathering Test Chamber is a premium environmenta...
	Automotive Wire Cut-Through Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Automotive Wire Cut-Through Tester is designed to evaluate the resistance of automotive...
	High-Collimation AAA-Grade Solar Simulator	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com TheHigh-Collimation AAA-Grade Solar Simulatoris designed to provide a concent...

Все товары поставщика

Похожие товары

	MMA-120 Handheld Arc Welder	Продавец: 871183	The MMA-120 Handheld Arc Welder from ChuangLi Electronic Technology Co., Ltd. is designed for con...
	SHX Series Circulating Fluidized Bed Steam Boiler	Продавец: Hebei Genjux Boiler Co.,Ltd	Capacity: 10-35 t/hWorking pressure: 1.25-2.5 MPaOperating temperature: 194-400 ℃Applicable to bi...
	YQ(Y)W Series Oil/Gas Fired Vertical Thermal Oil Boiler	Продавец: Hebei Genjux Boiler Co.,Ltd	Capacity: 7000-29200 KWOperating pressure: 0.8-1.0 MPaOperating temperature: 320℃Operating mode: ...
	DHL Series Coal-Fired Steam Boilers	Продавец: Hebei Genjux Boiler Co.,Ltd	Capacity: 35-75 t/hOperating pressure: 1.25-5.4 MPaOperating temperature: 194-485℃Applicable to b...
	SZL Series Biomass Steam Boiler	Продавец: Hebei Genjux Boiler Co.,Ltd	Capacity: 6-35 t/hWorking pressure: 1.0-2.5 MPaOperating temperature: 184-350 ℃Applicable fuel bi...