Coating Surface Performance Tester

Whats/App: +86 156 1874 6768

Web: standard-groups.com

Application

Electronic product surfaces: Evaluation of wear resistance and color fading of coatings on mobile housings and keypads

Paper and printing materials: Measurement of friction between paper surfaces to prevent paper jams in printers and copiers

Abrasive materials: Quantification of grinding performance and wear characteristics of sandpaper

Rubber materials: Wear resistance testing of rubber components, including observation of automotive tire wear behavior

Rubber–glass interfaces: Friction performance evaluation between rubber and glass, such as wiper blade interaction with windshields

Flat materials: Friction performance testing of various flat sheet and panel materials

Environmental testing: Friction and wear testing under oil immersion, elevated temperature, or cooling conditions

Coated surfaces: Friction, wear, and scratch testing of coatings across different material systems

Typical test samples include:

Plastic housings and coated components

Paper and paperboard materials

Rubber products and elastomers

Glass and coated glass surfaces

Films, sheets, and surface-treated panels

Standards

GB/T 6040-2008 Test Method for Wear Resistance of Metal Surfaces

GB/T 9279-2007 Paints and Varnishes — Cross-Cut Test

JIS K 7125 Plastics — Tribological Test Methods

JIS K 5600 Testing Methods for Paints and Varnishes (including scratch, abrasion, and adhesion tests)

JIS L 0823 Test Methods for Abrasion Resistance of Plastic Films and Sheets

JIS P 8139 Determination of Friction and Wear Properties of Coatings

JIS P 8147 Determination of Surface Friction Coefficient and Scratch Properties of Coatings

ASTM D1894 Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting

Parameters

Parameter Category	Specification
Sliding speed	5 – 6000 mm/min
Drive motor	AC servo motor
Drive mechanism	Gear and rack transmission
Sliding distance	1 – 100 mm
Motion mode	Single mode: stops automatically after preset distance
	Reciprocating mode: preset distance, up to 99.999.999 cycles
Measurement range	10 – 100 gf or 0 – 2000 gf
Worktable size	240 × 120 mm
Safety system	Overload protection (OVERLOAD)
Noise suppression	High-frequency noise suppression circuit
Zero adjustment	Digital servo automatic zeroing
Output (non-linearity)	0 – 5 V (within 0.05% FS)
Sensitivity switching	0 / 10 / 25 / 50 / 100% FS
Dynamic strain amplifier	S/N ratio: 60 dB (maximum sensitivity)
Frequency response	2 kHz / −3 dB
Filter	1 / 10 / 100 Hz low-pass filter
Operating environment	0 – 50 °C, ≤85% RH, non-condensing
Power supply	AC 100 V, 50/60 Hz
Main unit dimensions	W 630 × D 350 × H 580 mm

Features

Linear motion driven by a servo motor ensures stable and precise friction testing

Balanced mechanical arm structure minimizes the influence of adapter weight on vertical load

Direct transmission of friction force to the load sensor improves measurement accuracy

Supports a wide range of test heads and accessories for versatile surface performance evaluation

Touchscreen interface enables intuitive operation and real-time data display

Capable of testing under special environments, including lubricated, heated, or cooled conditions

Test Procedures

Fix the test specimen securely on the worktable.

Select and install the appropriate test head according to the test method.

Set test parameters such as speed, sliding distance, load, and motion mode.

Adjust environmental conditions if required (oil, heating, or cooling).

Start the test and monitor friction force and surface behavior in real time.

Complete the test automatically or manually after the preset conditions are met.

Analyze test results based on the applicable standard and test objective.

Maintenance Information

Clean the worktable and test heads after each test

Inspect mechanical arms and transmission components regularly

Verify load sensor performance and zero calibration periodically

Keep electronic components free from dust and moisture

Store accessories and weights properly to prevent damage

Other supplier products

	aatcc scorch & sublimation tester丨aatcc scorch & sublimation chamber	Whats/App: +86 156 1874 6768 Web: standard-groups.com Brief Introduction Scorch/Sublimation Tester is used in the laboratory to evaluate colour ...
	Tibial Tray Fatigue Testing Machine	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard YY/T 0810 (China): Specifies fatigue testing protocols for tibial trays in total ...
	Bench-top Mechanical load testing machine for photovoltaic modules	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application The machine is widely used for mechanical performance testing and structural v...
	Bending Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Pure Bending Tester analyzes hand movements-referred to as "bending"-performed by artis...
	Nasal Oxygen Cannula Airflow Resistance Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Nasal Oxygen Cannula Airflow Resistance Tester is designed in strict compliance with YY...

All supplier products

Same products

	Laser Chuck	Seller: Drake precision technology (changzhou) Co.,Ltd.	Laser Chuck Introduce foreign advanced technology and management concept, High precision pro...
	Power Pallet Jack For Sale	Seller: Jinan Hulk Machinery Co., Ltd	Power Pallet Jack For Sale Electric Pallet Truck For Sale As a supplier of power pallet jac...
	Multi Directional Forklift For Sale	Seller: Jinan Hulk Machinery Co., Ltd	Multi Directional Forklift For Sale Multi Directional Forklift For Sale As a supplier of mu...
	Narrow Aisle Forklift For Sale	Seller: Jinan Hulk Machinery Co., Ltd	Narrow Aisle Forklift For Sale Narrow Aisle Forklift For Sale As a supplier of , we provide...
	Electric Order Picker Supplier	Seller: Jinan Hulk Machinery Co., Ltd	Electric Order Picker Supplier Electric Order Picker Supplier As an supplier, we offer a co...