Coating Surface Performance Tester

Whats/App: +86 156 1874 6768

Web: standard-groups.com

Application

Electronic product surfaces: Evaluation of wear resistance and color fading of coatings on mobile housings and keypads

Paper and printing materials: Measurement of friction between paper surfaces to prevent paper jams in printers and copiers

Abrasive materials: Quantification of grinding performance and wear characteristics of sandpaper

Rubber materials: Wear resistance testing of rubber components, including observation of automotive tire wear behavior

Rubber–glass interfaces: Friction performance evaluation between rubber and glass, such as wiper blade interaction with windshields

Flat materials: Friction performance testing of various flat sheet and panel materials

Environmental testing: Friction and wear testing under oil immersion, elevated temperature, or cooling conditions

Coated surfaces: Friction, wear, and scratch testing of coatings across different material systems

Typical test samples include:

Plastic housings and coated components

Paper and paperboard materials

Rubber products and elastomers

Glass and coated glass surfaces

Films, sheets, and surface-treated panels

Standards

GB/T 6040-2008 Test Method for Wear Resistance of Metal Surfaces

GB/T 9279-2007 Paints and Varnishes — Cross-Cut Test

JIS K 7125 Plastics — Tribological Test Methods

JIS K 5600 Testing Methods for Paints and Varnishes (including scratch, abrasion, and adhesion tests)

JIS L 0823 Test Methods for Abrasion Resistance of Plastic Films and Sheets

JIS P 8139 Determination of Friction and Wear Properties of Coatings

JIS P 8147 Determination of Surface Friction Coefficient and Scratch Properties of Coatings

ASTM D1894 Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting

Parameters

Parameter Category	Specification
Sliding speed	5 – 6000 mm/min
Drive motor	AC servo motor
Drive mechanism	Gear and rack transmission
Sliding distance	1 – 100 mm
Motion mode	Single mode: stops automatically after preset distance
	Reciprocating mode: preset distance, up to 99.999.999 cycles
Measurement range	10 – 100 gf or 0 – 2000 gf
Worktable size	240 × 120 mm
Safety system	Overload protection (OVERLOAD)
Noise suppression	High-frequency noise suppression circuit
Zero adjustment	Digital servo automatic zeroing
Output (non-linearity)	0 – 5 V (within 0.05% FS)
Sensitivity switching	0 / 10 / 25 / 50 / 100% FS
Dynamic strain amplifier	S/N ratio: 60 dB (maximum sensitivity)
Frequency response	2 kHz / −3 dB
Filter	1 / 10 / 100 Hz low-pass filter
Operating environment	0 – 50 °C, ≤85% RH, non-condensing
Power supply	AC 100 V, 50/60 Hz
Main unit dimensions	W 630 × D 350 × H 580 mm

Features

Linear motion driven by a servo motor ensures stable and precise friction testing

Balanced mechanical arm structure minimizes the influence of adapter weight on vertical load

Direct transmission of friction force to the load sensor improves measurement accuracy

Supports a wide range of test heads and accessories for versatile surface performance evaluation

Touchscreen interface enables intuitive operation and real-time data display

Capable of testing under special environments, including lubricated, heated, or cooled conditions

Test Procedures

Fix the test specimen securely on the worktable.

Select and install the appropriate test head according to the test method.

Set test parameters such as speed, sliding distance, load, and motion mode.

Adjust environmental conditions if required (oil, heating, or cooling).

Start the test and monitor friction force and surface behavior in real time.

Complete the test automatically or manually after the preset conditions are met.

Analyze test results based on the applicable standard and test objective.

Maintenance Information

Clean the worktable and test heads after each test

Inspect mechanical arms and transmission components regularly

Verify load sensor performance and zero calibration periodically

Keep electronic components free from dust and moisture

Store accessories and weights properly to prevent damage

Other supplier products

	Chest Drainage Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The thoracic drainage tester is widely applied in the medical field, mainly used for monito...
	Textile Acid Printed Fabric Surface Wool Adhesion Meter	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards ISO 9073-4: Textile flatness measurement ASTM D3884: Abrasion resistance correl...
	Photo fill light box	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard CE & FCC Certified: Meets electromagnetic compatibility and safety standards ...
	Fiber Crimp Elasticity Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Fiber Crimp Elasticity Tester is a specialized instrument designed to measure the crimp...
	Bus Seat Durability Testing Machine	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com The Bus Seat Tester is designed to evaluate the durability, strength, and fat...

供应产品

Same products

	HDPE高速水冷双壁波纹管生产线	卖方: Shandong HUASU Plastic Technology Co.,Ltd.	机头模具采用双流道结构、氮化磨光处理机头，偏壁调整方便快捷，保证内外层壁厚均匀和稳定成型。 最新设计密闭压力水冷冷却结构，冷却充分，多点分布真空系统，效率更高，生产速度更快。 双层在线扩口功...
	PanEVAP & MVR system	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat...
	PanGAP wide gap welded plate heat exchanger	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel...
	PanBloc welded plate heat exchanger	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac...
	PanBox welded plate heat exchanger	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated...