Copper Mould Tube & Plate

Copper Mould Tube & Plate

We specially in supplying Copper Mould Tube, Crystallizing equipment of continuous casters, Mould cooling jacket, Repair of Metallurgical Copper Mould Tube, etc.

Equipments & Spare parts for Continuous Casting Machine.

3. Mould cooling jacket.

COPPER MOULD ALLOYS

The copper alloys chosen for the moulds must maintain their physical properties at the operating temperatures of the continuous casting process.

The temperature gradation from the inner wall of the mould to the outside face of the mould can cause serious distortion problems, and Metallurgical Copper Mould Tubeis imperative that the correct alloy is chosen for the various operating conditions.

Square Copper mould tubeSTANDARD MATERIALS

Phosphorus de-oxidised copper

This alloy has been proven to be excellent for the manufacture of moulds in the continuous casting of billets. The main composition of this alloy are Cu +Ag 99.90min, P0.0015 / 0.040.

Copper -Silver alloy

The addition of a small amount of silver, whilst not increasing the melting point of copper, does increase the recrystallisation temperature by almost 100℃, and also helps to give better thermal conductivity at the operating temperatures.

This alloy is normally used in moulds for the continuous casting of blooms and slabs .In this case, the moulds are much thicker than in the billet moulds, and the moulds temperature can be higher. The main composition of this alloy are Cu+Ag99.90 min. Ag 0.08 / 0.12 O 0.004 / 0.012.

Copper Mould Tube supplier

The continuous casting of molten steel into billets, blooms and slab products, has been highly refined over the years into an extremely sophisticated system. The continuous casting process is expected to produce metallurgically sound products at the lower possible cost, and this is being achieved in many steelworks throughout the world.

Copper mouldshave played an important role in the development of the continuous casting process. Their funcition is to receive the molten steel and to allow rapid heat transfer from the steel to the cooling water to enable quick solidification.

The mould must exhibit excellent thermal conductivity, be resistant for thermal erosion ,and be resistant to distortion from thermal stress. So far only copper and a few copper alloys meet the above conditions, both economically and technically.

Mould cooling jacket supplierSOLIDIFICATION

The rate of solidification in the continuous casting process dictates the speed of production. The molten steel, which is in contact with the inner faces of the copper mould, starts to sllidify as rapidly as the heat is extracted, forming a shell. The shell increases in thickness as more heat is extracted, and eventually total solidfication is achieved. the process is similar to the solidification of ingots in ingot moulds. In continuous casting, the whole process is speeded up, with the aim to produce and homogeneous shell growth. Consequently, the mould is an important part of the continuous casting process, and the manufactured quality of the mould plays and important role in their length of life.

INNER SURFACE COATINGS

Over the years, Metallurgists and Engineers have been working together to develop better continuous casting moulds. The steel companies require a more economical mould which will give a longer service life. Surface coating of the inner walls of the mould has given the best results to date. Coatings available are Chromium and Nickel plating. Also, a combination of the two give good results on slab casting.

SPECIFICATIONS OF COPPER MOULD

Square Copper mould tube

Square 60 x 60 - 350 x 350 (mm)

Rectangle 120 x 160 - 180 x 300 (mm)

Round Copper Mould tube

Diameter 100-400 (mm)

Size(mm): 90x90, 100x100, 110x110, 115x115, 120x120

130x130, 135x135, 140x140, 143x143, 150x150

155x155, 160x160, 165x165, 175x175, 180x180

200x200, 220x220, 100x170, 100x173, 130x240

150x200, 150x210, 150x220, 160x200, 160x220

150x225, 160x235, 165x225, 175x225, 180x220

200x240, 240x240, 235x235

Radius(mm): 4000, 5000, 5250, 6000, 7000, 7500, 8000, 9000, 10250, 10300, 11000, 12000

Length(mm): 700, 750, 780, 790, 800, 810, 812, 850, 900, 1000

Другие товары поставщика

	Magnesia-Carbon Brick	Magnesia-Carbon Brick Plant Introduction Sinometal refractory engineering Co., Ltd. is a modern comprehensive enterprise consisting of scientific r...
	Mill Rolls	Mill Rolls Metallurgical Rollsused for the modern cold and hot rolled strip tandem mills, medium-wide thick strip mills, profile steels, bars, high...
	Non-Invasive Ventilator	Non-Invasive Ventilator In the 6th Edition of China National health commission Coronavirus pneumonia treatment, there is equipment called Humidifie...
	Tundish Dry Vibration Mix	Tundish Dry Vibration Mix (1) Check whether the gas, compressed air and industrial electricity are normal, whether there is leakage, and whether al...
	RP Graphite Electrodes	RP Graphite Electrodes ourRP Graphite Electrodesare widely used in Electric Arc Furnace and Ladle furnace for making alloy steel or other metals an...

Все товары поставщика

Похожие товары

	For Mercedes-Benz-C-206 Modified Bumper Mould	Продавец: Taizhou Huangyan Chenpeng Mould Co., Ltd.	Taizhou Huangyan Chenpeng Mold Co., Ltd. is a professionalwholesale Mercedes-Benz-C-206 Modified ...
	Front Bumper Lower Lip Mould	Продавец: Taizhou Huangyan Chenpeng Mould Co., Ltd.	Introducing the for 2021 Honda CRV Front Bumper Lower Lip Mould: Elevate Your Driving Experienc...
	Bottle cap mold	Продавец: Taizhou Huangyan Yongsheng Mould Co., Ltd.	Taizhou Yongsheng Mould Co., Ltd. can produce cap moulds （）within 64 cavities. The hot runner or ...
	Plastic Injection Mould For 2009 Audi A5 Front Bumper	Продавец: Taizhou Huangyan Chenpeng Mould Co., Ltd.	Our Advantage:1.We have developed about 1000 PCS bumper mould since we founded.2.Our company's mo...
	Double Color Mold For Car Head Lighting Two-Shot Mold	Продавец: Taizhou Toolsong Mould Co., Ltd.	Double Color Mold For Car Head Lighting Two-Shot Mold Double color lens mold for car head lighti...