.

Copper Mould Tube & Plate

Copper Mould Tube & Plate

We specially in supplying Copper Mould Tube, Crystallizing equipment of continuous casters, Mould cooling jacket, Repair of Metallurgical Copper Mould Tube, etc.

Equipments & Spare parts for Continuous Casting Machine.

  1. Mould cooling jacket.

COPPER MOULD ALLOYS

The copper alloys chosen for the moulds must maintain their physical properties at the operating temperatures of the continuous casting process.

The temperature gradation from the inner wall of the mould to the outside face of the mould can cause serious distortion problems, and Metallurgical Copper Mould Tubeis imperative that the correct alloy is chosen for the various operating conditions.

Square Copper mould tubeSTANDARD MATERIALS

Phosphorus de-oxidised copper

This alloy has been proven to be excellent for the manufacture of moulds in the continuous casting of billets. The main composition of this alloy are Cu +Ag 99.90min, P0.0015 / 0.040.

Copper -Silver alloy

The addition of a small amount of silver, whilst not increasing the melting point of copper, does increase the recrystallisation temperature by almost 100℃, and also helps to give better thermal conductivity at the operating temperatures.

This alloy is normally used in moulds for the continuous casting of blooms and slabs .In this case, the moulds are much thicker than in the billet moulds, and the moulds temperature can be higher. The main composition of this alloy are Cu+Ag99.90 min. Ag 0.08 / 0.12 O 0.004 / 0.012.

Copper Mould Tube supplier

The continuous casting of molten steel into billets, blooms and slab products, has been highly refined over the years into an extremely sophisticated system. The continuous casting process is expected to produce metallurgically sound products at the lower possible cost, and this is being achieved in many steelworks throughout the world.

Copper mouldshave played an important role in the development of the continuous casting process. Their funcition is to receive the molten steel and to allow rapid heat transfer from the steel to the cooling water to enable quick solidification.

The mould must exhibit excellent thermal conductivity, be resistant for thermal erosion ,and be resistant to distortion from thermal stress. So far only copper and a few copper alloys meet the above conditions, both economically and technically.

Mould cooling jacket supplierSOLIDIFICATION

The rate of solidification in the continuous casting process dictates the speed of production. The molten steel, which is in contact with the inner faces of the copper mould, starts to sllidify as rapidly as the heat is extracted, forming a shell. The shell increases in thickness as more heat is extracted, and eventually total solidfication is achieved. the process is similar to the solidification of ingots in ingot moulds. In continuous casting, the whole process is speeded up, with the aim to produce and homogeneous shell growth. Consequently, the mould is an important part of the continuous casting process, and the manufactured quality of the mould plays and important role in their length of life.

INNER SURFACE COATINGS

Over the years, Metallurgists and Engineers have been working together to develop better continuous casting moulds. The steel companies require a more economical mould which will give a longer service life. Surface coating of the inner walls of the mould has given the best results to date. Coatings available are Chromium and Nickel plating. Also, a combination of the two give good results on slab casting.

SPECIFICATIONS OF COPPER MOULD

Square Copper mould tube

Square 60 x 60 - 350 x 350 (mm)

Rectangle 120 x 160 - 180 x 300 (mm)

Round Copper Mould tube

Diameter 100-400 (mm)

Size(mm): 90x90, 100x100, 110x110, 115x115, 120x120

130x130, 135x135, 140x140, 143x143, 150x150

155x155, 160x160, 165x165, 175x175, 180x180

200x200, 220x220, 100x170, 100x173, 130x240

150x200, 150x210, 150x220, 160x200, 160x220

150x225, 160x235, 165x225, 175x225, 180x220

200x240, 240x240, 235x235

Radius(mm): 4000, 5000, 5250, 6000, 7000, 7500, 8000, 9000, 10250, 10300, 11000, 12000

Length(mm): 700, 750, 780, 790, 800, 810, 812, 850, 900, 1000



Send product request

To: Sinometal Machinery Corp.
Your E-mail:
Message text:


Send to other suppliers

Other supplier products

 Tundish Dry Vibration Mix
Tundish Dry Vibration Mix Tundish Dry Vibration Mix (1) Check whether the gas, compressed air and industrial electricity are normal, whether there is leakage, and whether al...
RP Graphite Electrodes
RP Graphite Electrodes RP Graphite Electrodes ourRP Graphite Electrodesare widely used in Electric Arc Furnace and Ladle furnace for making alloy steel or other metals an...
Mill Rolls
Mill Rolls Mill Rolls Metallurgical Rollsused for the modern cold and hot rolled strip tandem mills, medium-wide thick strip mills, profile steels, bars, high...
Non-Invasive Ventilator
Non-Invasive Ventilator Non-Invasive Ventilator In the 6th Edition of China National health commission Coronavirus pneumonia treatment, there is equipment called Humidifie...
Graphite Electrodes
Graphite Electrodes Graphite electrodesincludingRP Graphite Electrodes, RPI, HP, SHP and UHP Graphite Electrodesare widely used in Electric Arc Furnace and Ladle furna...
All supplier products

Same products

SMC/BMC Framework
SMC/BMC Framework Seller: ZHEJIANG AOBANG TECHNOLOGY CO.,LTD SMC/BMC FrameworkDescription Strong plasticity, precise size, high insulation and high temperatu...
Shell Moulding
Shell Moulding Seller: ZHEJIANG AOBANG TECHNOLOGY CO.,LTD Shell MouldingDescription Mainly for injection molding, the cavity pressure should be considered...
Motor Mold
Motor Mold Seller: ZHEJIANG AOBANG TECHNOLOGY CO.,LTD Motor MoldDescription Mainly for injection molding, the design of the runner and the parting sur...
Low-Voltage Electrical Products
Low-Voltage Electrical Products Seller: ZHEJIANG AOBANG TECHNOLOGY CO.,LTD Low Voltage Electrical Appliance Mould List Mainly refers to circuit breakers, fuses, switch box...
Household Mould
Household Mould Seller: ZHEJIANG AOBANG TECHNOLOGY CO.,LTD Household MouldDescription Mainly for pressure molding, the cavity pressure should be considered...