Custom Seal Kit

The seal kit manufacturer Sanping custom seal kitsis one of the best partners in the construction machinery maintenance market. We use 1:1 real mechanical equipment for effective experimental detection, to ensure that each seal repair kitcan effectively adapt to the work requirements of each hydraulic system and sealing system, and can provide customized services according to different equipment requirements, and effectively provide scientific and correct solutions for customers.

How to Install a Seal Kitin a Hydraulic Cylinder?

Different seals have different installation methods, common types: reciprocating motion seals and skeleton oil seals for rotation. The installation method of the skeleton oil seal for rotation: the first step, when taking the oil seal out of the warehouse, check whether there are dust and sand and other impurities on the surface of the oil seal and the lip, so as to avoid these substances from damaging the lip and shaft during the shaft movement, causing leakage.

In the second step, for oil seals with more than two lips like TC, TA, TB, and TF, please fill the lip with grease, and for single-lip oil seals like SC, VC, and VB Apply grease to the end. The third step is to confirm that there is no foreign matter such as anti-rust oil or dust attached to the surface of the shaft and cavity. If there is any, please clean it.

The fourth step is to confirm that there are no burrs on the surface of the shaft cavity and chamfers, so as to prevent these burrs from damaging the lip during installation.

The fifth step is to assemble it into the cavity. It should be noted that the installation direction of the oil seal is that the sealing lip faces the sealing introduction side. The sixth step, when installing the oil seal, please use a special clamp to avoid the oil seal from tilting during installation. Installation method of hydraulic cylinder seals:

How to Select the Right o ring seal kitSize?

When we choose seals, we must consider the following important factors:

The pressure level and the length of the pressure cycle change have a great influence on the damage of the seal (such as extrusion). The higher the pressure, the greater the impact of other factors on the performance of the seal, such as temperature, speed, material of the seal, the gap between the piston and the cylinder, and the gap between the piston and the cylinder head.

It is difficult to describe the maximum service temperature and the minimum service temperature of a sealing material because this is the result of a series of factors. For the working temperature of the piston and the piston rod are different, they should be selected differently.

The friction between the seal and the sealing surface depends on many factors: surface roughness, surface characteristics, pressure, medium, temperature, seal material, seal type and movement speed.

Experience has shown that the characteristics of the surface of the cylinder piston and piston rod have a great influence on the life of the seal. Surface properties are often defined by the value of surface roughness Ra, which is the arithmetic mean of the absolute value of the surface shape away from the center line. However, these values cannot fully represent the influence of the surface condition on the seal, because even under the same roughness, different surface shape features can cause different degrees of seal wear on the seal.

Другие товары поставщика

	Floating Seal Fits Excavator	Floating oil sealis a kind of dynamic seal. It has super sealing performance in harsh working environment such as coal powder, silt, moisture, etc....
	LBH Dust Seal Fits Excavator	LHBSealFits Excavator Temperature ℃: -20/+200 Material: Viton Seal LBHMedium: high-temperature resistant dust ring seal ring Application:...
	Control Valve Seal Kit Fits PC200-6 Excavator	We have aftermarket replacementspool valve seal kitfor arm boom bucket, center joint, pilot valve, Hydraulic pump, swing motor, travel motor, gear ...
	Adjuster Seal Kit Fits PC400-5 Excavator	Model Applied: replacement part adjuster seal kits for Komatsu PC400-5 excavator parts. Material Properties: resistance to friction and wear, we...
	Boom Cylinder Seal Kit Fits Komastu PC200-6 Excavator	PC200-6 Repair kit/Seal boomkit is suitable use for 20- ton Komatsu excavator boom hydraulic cylinder. Complete parameters, stable performance, eas...

Все товары поставщика

Похожие товары

	Seal	Продавец: Тайчжоу Jiasheng Rubber & Plastic Co., Ltd.	Natural disasters, political instability, or economic downturns can disrupt the supply of raw...
	Silicon Carbide Pump Seals Silicon Carbide Bearings For Canned Motor Pump	Продавец: Zhejiang Guanyu Sealing Parts Co., Ltd.	Silicon carbide pump seals products Corrosion Resistance: The silicone material is highly resist...
	DOUBLE CARTRIDGE MECHANICAL SEALS	Продавец: Hangzhou Sealcon Fluid Machinery Co., Ltd	The double cartridge mechanical sealis a pre-assembled package of seal components, which make the...
	TC Seal	Продавец: Hangzhou Sealcon Fluid Machinery Co., Ltd	TC materials have features of high hardness, strength, abrasion resistance and corrosion resistan...
	Stainless Steel Seal	Продавец: Hangzhou Sealcon Fluid Machinery Co., Ltd	Stainless Steel is short for stainless acid resistant steel. It is called Stainless Steel with we...