Custom Seal Kit
The seal kit manufacturer Sanping custom seal kitsis one of the best partners in the construction machinery maintenance market. We use 1:1 real mechanical equipment for effective experimental detection, to ensure that each seal repair kitcan effectively adapt to the work requirements of each hydraulic system and sealing system, and can provide customized services according to different equipment requirements, and effectively provide scientific and correct solutions for customers.
How to Install a Seal Kitin a Hydraulic Cylinder?
Different seals have different installation methods, common types: reciprocating motion seals and skeleton oil seals for rotation. The installation method of the skeleton oil seal for rotation: the first step, when taking the oil seal out of the warehouse, check whether there are dust and sand and other impurities on the surface of the oil seal and the lip, so as to avoid these substances from damaging the lip and shaft during the shaft movement, causing leakage.
In the second step, for oil seals with more than two lips like TC, TA, TB, and TF, please fill the lip with grease, and for single-lip oil seals like SC, VC, and VB Apply grease to the end. The third step is to confirm that there is no foreign matter such as anti-rust oil or dust attached to the surface of the shaft and cavity. If there is any, please clean it.
The fourth step is to confirm that there are no burrs on the surface of the shaft cavity and chamfers, so as to prevent these burrs from damaging the lip during installation.
The fifth step is to assemble it into the cavity. It should be noted that the installation direction of the oil seal is that the sealing lip faces the sealing introduction side. The sixth step, when installing the oil seal, please use a special clamp to avoid the oil seal from tilting during installation. Installation method of hydraulic cylinder seals:
How to Select the Right o ring seal kitSize?
When we choose seals, we must consider the following important factors:
The pressure level and the length of the pressure cycle change have a great influence on the damage of the seal (such as extrusion). The higher the pressure, the greater the impact of other factors on the performance of the seal, such as temperature, speed, material of the seal, the gap between the piston and the cylinder, and the gap between the piston and the cylinder head.
It is difficult to describe the maximum service temperature and the minimum service temperature of a sealing material because this is the result of a series of factors. For the working temperature of the piston and the piston rod are different, they should be selected differently.
The friction between the seal and the sealing surface depends on many factors: surface roughness, surface characteristics, pressure, medium, temperature, seal material, seal type and movement speed.
Experience has shown that the characteristics of the surface of the cylinder piston and piston rod have a great influence on the life of the seal. Surface properties are often defined by the value of surface roughness Ra, which is the arithmetic mean of the absolute value of the surface shape away from the center line. However, these values cannot fully represent the influence of the surface condition on the seal, because even under the same roughness, different surface shape features can cause different degrees of seal wear on the seal.
Send product request
Other supplier products
 |
Sanping Back Up Ring | Sanping Back Up Ring China buck up ring seal is a thin ring designed to prevent the O-ring from extruding under pressure. They are installed in th... |
 |
Control Valve Seal Kit Fits PC200-6 Excavator | We have aftermarket replacementspool valve seal kitfor arm boom bucket, center joint, pilot valve, Hydraulic pump, swing motor, travel motor, gear ... |
 |
Sanping Seal Kits for Hitachi | hitachi seal kitis suitable for all kinds of Hitachi excavators, Hitachi loaders, Hitachi bulldozers, etc.The hitachi bucket seal kit, as always, p... |
|
|
Custom Seal Kit | The seal kit manufacturer Sanping custom seal kitsis one of the best partners in the construction machinery maintenance market. We use 1:1 real mec... |
 |
14589129 Boom Cylinder Seal Kit Fits Volvo EC210 Excavator | Cylinder hydraulic repair kit 14589129EC210 BOOM is suitable for VOLVO 20 ton excavators commonly used on construction sites. VOLVO brand machines ... |
Same products
 |
Split Oil Seal | Seller: Xingtai Hongyu Sealing Technologies Co., Ltd | Split type skeleton oil sealis a kind of industrial seal, which is simply used to seal the medium... |
 |
oil seal kit | Seller: Xingtai Nok-Cn Metal Seal Manufacturing Co., Ltd. | oil seal kit is a collection of various Oil Seals and related components designed for specif... |
 |
High-Performance Valve Cover Gasket | Seller: Xingtai Nok-Cn Metal Seal Manufacturing Co., Ltd. | High-Performance Valve Cover Gasket Product Description: High-Performance Valve Cover Gasket... |
 |
freeze plug | Seller: Xingtai Nok-Cn Metal Seal Manufacturing Co., Ltd. | freeze plug We not only will try our best to offer excellent services to every customer, but... |
 |
Discover the Excellence of Bonded Seals | Seller: Xingtai Nok-Cn Metal Seal Manufacturing Co., Ltd. | Discover the Excellence of Bonded Seals Discover the Excellence of Bonded Seals Enhance you... |
