Custom Seal Kit
The seal kit manufacturer Sanping custom seal kitsis one of the best partners in the construction machinery maintenance market. We use 1:1 real mechanical equipment for effective experimental detection, to ensure that each seal repair kitcan effectively adapt to the work requirements of each hydraulic system and sealing system, and can provide customized services according to different equipment requirements, and effectively provide scientific and correct solutions for customers.
How to Install a Seal Kitin a Hydraulic Cylinder?
Different seals have different installation methods, common types: reciprocating motion seals and skeleton oil seals for rotation. The installation method of the skeleton oil seal for rotation: the first step, when taking the oil seal out of the warehouse, check whether there are dust and sand and other impurities on the surface of the oil seal and the lip, so as to avoid these substances from damaging the lip and shaft during the shaft movement, causing leakage.
In the second step, for oil seals with more than two lips like TC, TA, TB, and TF, please fill the lip with grease, and for single-lip oil seals like SC, VC, and VB Apply grease to the end. The third step is to confirm that there is no foreign matter such as anti-rust oil or dust attached to the surface of the shaft and cavity. If there is any, please clean it.
The fourth step is to confirm that there are no burrs on the surface of the shaft cavity and chamfers, so as to prevent these burrs from damaging the lip during installation.
The fifth step is to assemble it into the cavity. It should be noted that the installation direction of the oil seal is that the sealing lip faces the sealing introduction side. The sixth step, when installing the oil seal, please use a special clamp to avoid the oil seal from tilting during installation. Installation method of hydraulic cylinder seals:
How to Select the Right o ring seal kitSize?
When we choose seals, we must consider the following important factors:
The pressure level and the length of the pressure cycle change have a great influence on the damage of the seal (such as extrusion). The higher the pressure, the greater the impact of other factors on the performance of the seal, such as temperature, speed, material of the seal, the gap between the piston and the cylinder, and the gap between the piston and the cylinder head.
It is difficult to describe the maximum service temperature and the minimum service temperature of a sealing material because this is the result of a series of factors. For the working temperature of the piston and the piston rod are different, they should be selected differently.
The friction between the seal and the sealing surface depends on many factors: surface roughness, surface characteristics, pressure, medium, temperature, seal material, seal type and movement speed.
Experience has shown that the characteristics of the surface of the cylinder piston and piston rod have a great influence on the life of the seal. Surface properties are often defined by the value of surface roughness Ra, which is the arithmetic mean of the absolute value of the surface shape away from the center line. However, these values cannot fully represent the influence of the surface condition on the seal, because even under the same roughness, different surface shape features can cause different degrees of seal wear on the seal.
在线联系供应商
Other supplier products
 |
Control Valve Seal Kit Fits PC200-6 Excavator | We have aftermarket replacementspool valve seal kitfor arm boom bucket, center joint, pilot valve, Hydraulic pump, swing motor, travel motor, gear ... |
 |
Sanping O Ring Kit Box | The o-ring kit is also called the o ring set box, which is mainly used in the maintenance market. Construction heavy machinery includes excavators,... |
 |
14589129 Boom Cylinder Seal Kit Fits Volvo EC210 Excavator | Cylinder hydraulic repair kit 14589129EC210 BOOM is suitable for VOLVO 20 ton excavators commonly used on construction sites. VOLVO brand machines ... |
 |
4649049 Boom Seal Kit Fits ZAX330-3 Excavator | Accessories for Hitachi excavators: EX60, EX60-2/3, EX60-5, EX100, EX100-2/3, EX100-5, EX120, EX120-2, EX120-5, EX150, EX150-5/160-5, EX200, EX200-... |
 |
MPI Rod Seal Fits Excavator | MPI Rod Seal Fits Excavator MPI seals, a type of custom oil seals, are widely used in construction machinery, ceramic machinery, mining machinery,... |
Same products
 |
Quick-response Mechanical seal M74N-140 for power generation | 卖方: DONGFANG YOYIK (DEYANG) ENGNIEERING CO; LTD | "Quick-response Mechanical seal M74N-140 for power generation Is YOYIK for the use of turbine uni... |
 |
Oil Seal 118*160*13 for Truck Auto Part Shaft NBR KDIK oil seal factory | 卖方: Xingtai Honglei Seal Manufacturing Co., Ltd | Hot sale various high quality Truck oil seal from Chinaleading manufacturer. Our products are eff... |
 |
Bh1941g Engine Timing Cover Seal Engine Camshaft Oil Seal | 卖方: Xingtai Honglei Seal Manufacturing Co., Ltd | A Suzuki oil sealis a mechanical seal used to seal the gaps between the rotating shaft and the st... |
 |
Transmission Oil Seal Bh4371e Tb 35*50*9.5 OEM for Toyota | 卖方: Xingtai Honglei Seal Manufacturing Co., Ltd | Automotive oil sealsplay critical roles in different types of four wheeler vehicles. They are pri... |
 |
UN Oil Seal | 卖方: Xingtai Dingtong Rubber and Plastic Products Co., Ltd | A pliable, non-metallic PU ringis ingeniously nestled within a precision-machined groove or seaml... |
