SMC/BMC Antenna Reflector

• 

(1) High precision, high efficiency, and high gain.

The most important job of using SMC/BMC for the manufacture of antennas is to fully exploit its features and achieve high precision in antenna design from product design and process. Under the condition that the shrinkage ratio of the material and the BMCmolding shrinkage rate have been considered in the mold size design, the BMC reflectorsurface has a smaller shape from the original design paraboloid after molding. That is, the accuracy of the SMC/BMC molded antenna is completely guaranteed by the accuracy of the mold. The rms value of the SMC/BMC antenna molded integral reflection surface is 0.25 mm, and the rms value of the single-piece reflection surface of the split antenna is less than 0.3 mm, and the rms value of the reflective surface after assembly is less than 0.6 mm.

(2) Corrosion resistance

Conventional antenna materials such as aluminum plates and steel plates are made of metal materials, not as good as SMC/BMC which as a non-metal dielectric composite material in terms of acid resistance, alkali, salt, and corrosion resistance. The Pikington laboratory in the United States used infrared to analyze the surface of SMC/BMCmaterials and found that its surface is covered by additives, resin, and very fine calcium acid filler. It has good acid resistance, water resistance and corrosion resistance. The antenna reflection made by this material is solved the disadvantage of the traditional metal material antenna is easy to corrode. In coastal areas, rainy, humid areas and areas with excessive acid rain, the anti-corrosion advantages of SMC molded antennas are particularly prominent. The SMC/BMC molded antenna samples were placed in 130 highly corrosive chemical environments at an ambient temperature of 50 ° C. The results showed that the test samples showed little or no change.

(3) Long life

The average aluminum plate antenna is as small as 2-3 years in the coastal area, and more often 4-6 years, and it will generally be damaged by salt spray erosion and aging. The most obvious example is the cable TV (CATV) in Taiwan, which was built earlier than the mainland. It is estimated that there are nearly 1000 satellite TV receiving antennas on the island, all built in the mid-1980s, all of which were aluminum plate antennas, until the early 1990s. , that is, has begun to replace. The service life of SMC molded antennas is generally more than 15 years; PROMLIN's prototype SMC molded antennas in 1985 are still working normally, and they are subject to typhoons and heavy rain every year.

(4) Strong wind resistance

Since the antenna reflection surface is designed during the molding process, multiple longitudinal and circumferential rib structures are designed. According to the structural strength calculation, the SMC antenna can withstand a wind load of 45 m/s, which shows its remarkable structural rigidity and strength.

(5) Special reflective layer technology

The reflective surface of the SMC antenna uses a metal aluminum mesh as a reflective layer of electromagnetic waves. The aluminum mesh in the finished antenna is evenly embedded under the surface SMC, which can reflect electromagnetic waves and insulate the atmosphere, and plays a good protective role.

(6) Good consistency, no deformation, easy to transport and install

Because SMC antenna adopts membrane pressure technology under high temperature and high pressure. Its material properties and processing technology determine the unparalleled consistency of SMC antennas with other antennas. This not only ensures the accuracy and high gain of the antenna, but also is very easy to install and debug. SMC, commonly known as "glass reinforced plastic", has the characteristics of no deformation, which eliminates the adverse effects of antenna deformation on the satellite receiving system during transportation.

SMC and BMC compositerequire heating rather than cooling systems. The temperature of the mold is usually between 130 and 160. It is very important to keep the temperature of the mold and the exhaust gas when designing the mold. The mold is easier to fill, the product is not easy to be deformed, and the surface is better. Commonly used heating systems are steam, oil and electric heating rods.

Vacuum assisted systems for BMC and SMC molds: Products with Class A surfaces are usually vacuum-assisted, and the internal cavity and vacuum insulation of the mold are very important. The mold must have a sensor and a vacuum system to measure the mold temperature and pressure vacuum. Production SMC and BMC molding: must guarantee high quality, long life and economy. Aobang Technology Co., Ltd.'s years of experience in the production of SMC and BMC molds and proficiency in machine, mold, material and process can ensure the maximum benefit of customers.

Другие товары поставщика

	Auto Parts And Accessories	Auto Parts Description Parts made from sheet molding compound (SMC) are typically 25-35% lighter than steel parts and aluminum products of the same...
	BMC/SMC Molds	Custom high Precision Compression/bulk molding compound manufacturingwith fast lead time BMC/SMC Mould Manufacturer We mainly use injection mol...
	BMC/SMC Mould	BMC/SMC plasticMoulding Description: We mainly use injection molding and pressure molding as the methods. When designing the flow channel and part...
	BMC, SMC, GRP, GFK Roof Tiles	Aobang composite roofing tiles is divided into: BMC roofing tiles, SMC roofing tiles, GRP roof tiles, GFK roofing tiles. Due to the excellent prop...
	Low-Voltage Electrical Products	Low Voltage Electrical Appliance Mould Manufacturer Mainly refers to circuit breakers, fuses, switch boxes, transformers, electric control boxes, ...

Похожие товары

	Индивидуальная форма двигателя	Продавец: 846123	90 Трехрядная высокоскоростная прогрессивная штамповочная формаИндивидуальная моторная пресс-форм...
	Car Mat Aluminium Vacuum Mould	Продавец: Hebei Shuiyuan Trading Co., Ltd	Product Description Vacuum molding is the most popular technology for shaping plastic raw mate...
	Auto Mould-Safe and Convenient Operation	Продавец: Taizhou Wanda Plastic Mould Co.,Ltd.	Product Name Auto Parts Mould Brand Wanda Mould Model No specific Model Material S136/H1...
	SMC Cable Braket	Продавец: ZHEJIANG AOBANG TECHNOLOGY CO.,LTD	The SMC cablebracket is a combination consisting of a cable bracket, a post and a fixed pin. The ...
	SMC/BMC Antenna Reflector	Продавец: ZHEJIANG AOBANG TECHNOLOGY CO.,LTD	(1) High precision, high efficiency, and high gain. The most important job of using SMC/BMC for ...