AKRON abrasion testing machine

Product Introduction:

AKRON wear testing machine is used with the balance, specially testing the wear resistance of rubber products such as soles, tires, car tracks, etc. The counters are electronic automatic, which can set the wear revolution, and automatically stop when the set revolution is reached.

Meet the standard:

GB/T 1689 standard

Test size:

Outer diameter 2 ", inner diameter 1/2 ", thickness 1/2 ", circumference 220mm, hardness 60——70

Machine operation method:

1. Prepare the core of the specimen according to the conditions of obtaining the specimen. And record its exact weight.

2. Fix the specimen core on the core shaft seat, and then adjust the Angle of the specimen. （Usually set to 15∘）

3. Different test methods are divided into high standards and low standards according to material requirements.

3.1 High standard requirements:

a. Angle （the Angle between the test piece and the grinding wheel）15∘

b. Load :6 pounds

c. Pre-grinding revolutions :300 revolutions

d. Remove the specimen core, brush with a clean brush to remove the powder, then weigh the exact weight with a precision balance, and record the weight of the sample before the test

e. Install the specimen core and set the wheel rotation times :3000 revolutions

f. After the wear is completed, remove the specimen, brush with a clean brush to remove the powder, and then weigh the accurate weight with a precision balance, which is the weight of the sample after the test

g. Substitute the formula to calculate the grinding amount

3.2 Low standard requirements:

a. Angle （the Angle between the test piece and the grinding wheel）15∘

b. Load :2 pounds

c. Pre-grinding revolutions :200 revolutions

d. Remove the specimen core, brush with a clean brush to remove the powder, then weigh the exact weight with a precision balance, and record the weight of the sample before the test

e. Load back the specimen core and set the wheel rotation times :2000 revolutions

f. After wearing, remove the specimen, brush with a clean brush to remove the powder, and then weigh the exact weight with a precision balance

This is the test weight after the test

g. Substitute the formula to calculate the grinding amount

4. After all specimens have been tested, remove the weight and store it, and remove the debris on the machine.

Wear value calculation method:

Wear （volume m1）== Weight before test - weight after test

Specific gravity algorithm:

a. If the test material is heavier than water

Specific gravity = Weight in air ÷（weight in air - weight of sample in water）

b. If the test material is lighter than water

Specific gravity = weight in air ÷ volume

Technical parameters:

Grinding wheel diameter Φ150mm, 40mm（w）， particle size 36#

Grinding wheel speed 34±1r/min

The incline range of the test material is adjustable from 0 to 35°

Test shaft speed （GB）76±2r/min

Load 26.7N±0.2

Counter LED, 0——99,999,999

Volume （W×D×H） 60 × 50 × 45cm

Weight （approx） 60 kg

Power 1 #,AC220V, 50Hz （depending on country or designation）

Другие товары поставщика

	G506 Mask Automatic Filter Performance Tester	Description:The latest G506 mask automatic filter performance tester uses the most advanced technology and design concepts, to meet a variety of te...
	Wire bending tester	Product Introduction: Wire bending tester meets JIS-C-3005 test standard. The sample is inserted through the specified round hole according to thi...
	Fabric Downproof Tester(Rolling Box)	TRANSLATE with x English Arabic Hebrew Polish Bulgarian Hindi Portuguese Catalan Hmong Daw Romanian ...
	Tabletop Light Fastness Tester	TRANSLATE with x English Arabic Hebrew Polish Bulgarian Hindi Portuguese Catalan Hmong Daw Romanian ...
	Mercury Lamp Solar Aging Tester	TRANSLATE with x English Arabic Hebrew Polish Bulgarian Hindi Portuguese Catalan Hmong Daw Romanian ...

Все товары поставщика

Похожие товары

	Air Permeability Tester STD- F8	Продавец: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...
	Surface Performance Tester STD-FB4 - A	Продавец: Standard International Group (HK) Limited	Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti...
	Compression Tester STD - FB3 - A	Продавец: Standard International Group (HK) Limited	TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar...
	Single - Strand Bending Tester STD - FB2 - SH	Продавец: Standard International Group (HK) Limited	Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ...
	Bending Tester STD- FB2 - S	Продавец: Standard International Group (HK) Limited	Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig...