AKRON abrasion testing machine
Product Introduction:
AKRON wear testing machine is used with the balance, specially testing the wear resistance of rubber products such as soles, tires, car tracks, etc. The counters are electronic automatic, which can set the wear revolution, and automatically stop when the set revolution is reached.
Meet the standard:
GB/T 1689 standard
Test size:
Outer diameter 2 ", inner diameter 1/2 ", thickness 1/2 ", circumference 220mm, hardness 60——70
Machine operation method:
1. Prepare the core of the specimen according to the conditions of obtaining the specimen. And record its exact weight.
2. Fix the specimen core on the core shaft seat, and then adjust the Angle of the specimen. （Usually set to 15∘）
3. Different test methods are divided into high standards and low standards according to material requirements.
3.1 High standard requirements:
a. Angle （the Angle between the test piece and the grinding wheel）15∘
b. Load :6 pounds
c. Pre-grinding revolutions :300 revolutions
d. Remove the specimen core, brush with a clean brush to remove the powder, then weigh the exact weight with a precision balance, and record the weight of the sample before the test
e. Install the specimen core and set the wheel rotation times :3000 revolutions
f. After the wear is completed, remove the specimen, brush with a clean brush to remove the powder, and then weigh the accurate weight with a precision balance, which is the weight of the sample after the test
g. Substitute the formula to calculate the grinding amount
3.2 Low standard requirements:
a. Angle （the Angle between the test piece and the grinding wheel）15∘
b. Load :2 pounds
c. Pre-grinding revolutions :200 revolutions
d. Remove the specimen core, brush with a clean brush to remove the powder, then weigh the exact weight with a precision balance, and record the weight of the sample before the test
e. Load back the specimen core and set the wheel rotation times :2000 revolutions
f. After wearing, remove the specimen, brush with a clean brush to remove the powder, and then weigh the exact weight with a precision balance
This is the test weight after the test
g. Substitute the formula to calculate the grinding amount
4. After all specimens have been tested, remove the weight and store it, and remove the debris on the machine.
Wear value calculation method:
Wear （volume m1）== Weight before test - weight after test
Specific gravity algorithm:
a. If the test material is heavier than water
Specific gravity = Weight in air ÷（weight in air - weight of sample in water）
b. If the test material is lighter than water
Specific gravity = weight in air ÷ volume
Technical parameters:
Grinding wheel diameter Φ150mm, 40mm（w）， particle size 36#
Grinding wheel speed 34±1r/min
The incline range of the test material is adjustable from 0 to 35°
Test shaft speed （GB）76±2r/min
Load 26.7N±0.2
Counter LED, 0——99,999,999
Volume （W×D×H） 60 × 50 × 45cm
Weight （approx） 60 kg
Power 1 #,AC220V, 50Hz （depending on country or designation）
Send product request
Other supplier products
 |
Car seat headrest static strength tester | Applicable standards: GB 11550-2009 "Automobile seat headrest strength requirements and test methods" : This standard specifies the static strengt... |
 |
Air Permeability Tester | Air Permeability TesterAir Permeability Tester of textile fabrics complies with ASTM D737, ISO 9237/7231, BS 5636, etc. It is used to test the resi... |
 |
Carbide wear tester | Applicable standards: GB/T 34501-2017: This standard specifies the wear resistance test method of cemented carbide, which is suitable for testing ... |
 |
Velcro Fatigue Tester | Product Information: Velcro Fatigue Testeris designed for opening and closing the hook and loop fasteners, A hook and loop fastener is repeatedly ... |
 |
Protective clothing acid and alkali resistance test equipment | Protective clothing acid and alkali resistance test equipment is used to determine acid and alkali impermeability of permeable acid and alkali prot... |
Same products
 |
Air Permeability Tester STD- F8 | Seller: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | Seller: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | Seller: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | Seller: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | Seller: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
