Battery impact tester

　The test sample cell is placed on a flat surface with a 15.8±0.2mm（5/8 in）

diameter rod placed in a cross position over the center of the sample. A 9.1kg or

10kg weight is dropped from a certain height （610mm or 1000mm） onto the

sample. cylinder

　　When the battery is subjected to impact test, its vertical axis should be parallel

to the plane and perpendicular to the vertical axis of the steel column. The most

axis of the square battery is perpendicular to the steel column, and the largest surface

is perpendicular to the impact direction. Each battery receives only one impact test.

The battery does not catch fire or explode.

Meet the standard

　　GBIT31485-2015 "Safety requirements and test methods of power Batteries for

Electric Vehicles"

　　GB/T31241-2022 "Safety requirements for lithium-ion batteries and battery packs

for portable electronic products.

　　UN383 United Nations Manual of Tests and Standards for the Transport of

Dangerous Goods

　　IEC62133 "Safety requirements for batteries （groups） composed of cells and for

use in portable equipment"

　　UL1642-2012 "Inner Battery Standard"

Main parameter

　　Inner box size :550x550x1440mm（W x D x H）

　　Equipment dimensions :660x900x1720mm（W x D x H）

　　Material :SUS201 stainless steel plate, thickness 1.2mm and coated with Teflon

　　Outer box material: 1.5mm thick cold rolled steel plate paint treatment

　　Observation window: 250x250mm tempered glass, transparent window with

stainless steel mesh.

　　Lighting device: The machine is equipped with a light inside to facilitate the

observation of the state of the tested sample.

　　Smoke outlet: 100mm in diameter, located at the rear of the box.

　　Pressure relief port: The opening size is 200x200mm, located at the back of the

box. When the sample is exploded, the pressure relief port will pop open and remove

the pressure.

　　Door: single door open left, door equipped with safety limit switch, side equipped

with explosion-proof chain to ensure the safety of personnel.

　　Ball weight: 9.1kg, 10kg, 0.1kg

　　Impact height :0-1000mm, commonly used test height 610 —— 25mm

　　Control mode: touch screen control

　　Displacement accuracy: 5mm soil

　　Impact mode: lift the falling ball to a certain height and release it. The falling

ball falls freely in the vertical direction without tilting or shaking.

　　Metal rod: Diameter 15.8±0.2mm steel rod

　　Maximum battery size :200x200x200mm

　　Impact surface :45# steel paint treatment, thickness 15mm

　　Equipment weight :270kg

　　Power supply :AC220V

　　Power :600W

Другие товары поставщика

	Electrolyte wettability test system	Standard ASTM D724-98: Standard Test Method for Surface Wettability of Paper (Angle-of-Repose Method Adapted) ISO 8296: Plastics – Determ...
	Vertical Flammability Chamber	VTEC Vertical Flammability Chamber： Testing Standards: ASTM D6413-99. DOC-FF 3/71. CALIF TB-117. GB/T 5455. CPAI-84 Applications: Vertical Flamm...
	Diaper impurity testing machine	Introduction: The diaper impurity detector is used to detect the impurities remaining inside the diaper under a certain strong light irradiation. ...
	Car seat center of gravity measuring tester	Main parameters: Measuring range:refers to the maximum and minimum range of the center of gravity of the seat that the tester can measure. This pa...
	Microbial Barrier Test device	Product Introduction: Y/T 0471.5-2017 is a newly updated standard, which specifies the experimental method for evaluating the bacteria-inhibiting ...

Все товары поставщика

Похожие товары

	Air Permeability Tester STD- F8	Продавец: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...
	Surface Performance Tester STD-FB4 - A	Продавец: Standard International Group (HK) Limited	Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti...
	Compression Tester STD - FB3 - A	Продавец: Standard International Group (HK) Limited	TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar...
	Single - Strand Bending Tester STD - FB2 - SH	Продавец: Standard International Group (HK) Limited	Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ...
	Bending Tester STD- FB2 - S	Продавец: Standard International Group (HK) Limited	Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig...