E-bike chassis dynamometer testing machine

Electric bicycles are complex systems involving mechanical, electrical, and control components. Evaluating their performance and compliance with safety and efficiency standards requires precise and repeatable testing that is difficult to achieve in outdoor environments due to varying weather, traffic, and road conditions. An Electric Bicycle Chassis Dynamometer System addresses this need by providing a consistent platform for comprehensive e-bike testing.

Standard

EN 15194:Cycles - Electrically power assisted cycles - EPAC Bicycles

ISO 4210:Cycles - Safety requirements for bicycles

UL 2849:Standard for Electrical Systems for eBikes

Application

Measuring motor efficiency, power output, and torque characteristics of e-bikes.

Evaluating battery range and energy consumption under simulated riding conditions.

Simulating various road loads, inclines, and driving cycles.

Testing electromagnetic compatibility (EMC) by providing a stable environment.

Conducting endurance and durability testing on e-bike components.

Verifying compliance with national and international standards for e-bike performance and safety.

Research and development of new e-bike designs, motors, batteries, and control strategies.

Quality control and validation during the e-bike manufacturing process.

Product Advantages

Provides a highly controlled and repeatable testing environment, eliminating variables from outdoor riding.

Enables precise and accurate measurement of critical e-bike performance parameters.

Allows for rapid and efficient testing for product development and quality control.

Enhances safety by performing tests in a controlled indoor setting rather than on roads.

Supports compliance testing against various national and international e-bike standards.

Facilitates detailed data acquisition and analysis for in-depth performance evaluation.

Offers versatility to simulate a wide range of riding conditions and custom test cycles.

Accommodates various e-bike types and sizes through adjustable mounting systems.

Parameters

Item	Detail
Loading Method	Inertia
Maximum Power	200 kW (300 HP)
Max Speed	350 km/h
Roll Inertia	8.16 m²·kg
Roll Diameter	450 mm
Roll Width	235 mm
Max Impasto	1.57 m
Vehicle Size	e - bike

Accessoriess

Roller

Power absorption device

Inertia simulation device

Drive motor

Speed sensor, etc.

Test Procedures

Preparation: Ensure the dynamometer is in good working order and prepare the necessary tools and equipment for the test. Check that the electric vehicle under test meets the test requirements, such as being fully charged and free of malfunctions.

Connect the power supply: Connect the electric vehicle to the dynamometer and switch on the power. At this point, the dynamometer should be in a "no-load" state.

Set parameters: Set the appropriate parameters according to the test requirements, such as test time and speed range.

Start the test: After confirming that all parameters are set correctly, start the test program. The dynamometer will perform the test according to the set parameters and record the test data.

End the test: After the test is completed, close the test program, disconnect the power supply, and remove the electric vehicle. The test results can then be viewed and data analysis can be performed.

Другие товары поставщика

	Burning Manikin System,Burn Test Manikin for sale	The burning manikin system is used to test the overall thermal protection performance of protective clothing.Complete combustion manikin system, wh...
	Flame Durability Testing Machine,Continuous Burning Time Tester for Liquids,ISO 9038	Introduction When the hazardous liquid is heated to 0.5 ºC and 75 ºC, flame durability tester is used to evaluate the continuous burning...
	Catheter Residual Vacuum Tester	The Catheter Residual Vacuum Tester is a professional device used to detect the residual vacuum in respiratory suction catheters, aiming to ensure ...
	Electric pencil hardness tester	The Electric Pencil Hardness Tester is designed to determine the surface hardness of coating layers applied to finished products by means of a stan...
	Resistance to flame propagation tester,ECE R118 Annex 10	Introduction This equipment is designed and manufactured according to ECE R118 Annex 10. This model is intelligent, with PLC and touch screen in...

Все товары поставщика

Похожие товары

	Full-Body Garment Stress Tester,FZ/T 70015	Продавец: Standard International Group (HK) Limited	TheFull-Body Garment Stress Testeris a precision instrument designed to quantify the pressure exe...
	Industrial Dry Cleaning Machine,industrial garment steamer	Продавец: Standard International Group (HK) Limited	TheIndustrial Dry Cleaning and Energy-Saving Dryer Machinesare designed for high-performance, rel...
	MST Medical Compression Stocking Tester,compression sock tester	Продавец: Standard International Group (HK) Limited	The MST Medical Compression Stocking Tester is a professional instrument designed to evaluate the...
	MMT Liquid Water Separation Tester,MMT Liquid Water Analysis Tool	Продавец: Standard International Group (HK) Limited	Applications Textile Manufacturing:Testing waterproof fabrics for outdoor gear R&D:Developi...
	Dental material color stability tester	Продавец: Standard International Group (HK) Limited	Application The applications of color stability testers for dental materials are mainly reflecte...